Speco VIP2P1 Скачать руководство пользователя страница 67

Страница: 67 / 72

3.8 Resetting to the factory default settings

To reset this network camera to the original factory settings, go to the Setup>System> Maintenance

web page (described in “3.5.4 System > Maintenance”) or use the Reset button on This network
camera, as described below

• Using the Reset Button

Follow the instructions below to reset this network camera to the factory default settings using
the Reset button.

1. Switch off this network camera by disconnecting the power adapter.

2. Press and hold the Reset button with a straightened paperclip while reconnecting the power.

3. Keep the Reset button pressed during about 2 seconds.

4. Release the Reset button.

5. This network camera resets to factory defaults and restarts after completing the factory

reset.

Caution:

When performing a Factory Reset, you will lose any settings you have saved.

Содержание VIP2P1









































































Результаты поиска

Содержание VIP2P1

Отзывы:

Похожие инструкции для VIP2P1

Бренды по названию

Популярные бренды

Speco VIP2P1, Инструкция по эксплуатации

Результаты поиска

Содержание VIP2P1

Отзывы:

Похожие инструкции для VIP2P1

Бренды по названию

Популярные бренды