Speck SSM-24 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 61

Speck SSM-24 Скачать руководство пользователя страница 20

Chapter 3

Installation Section

Connecting the

Power Supply

Before connecting the circular DC power supply connector to the SSM,
make certain the power supply is not plugged in.

To connect the power supply to the main mixer, fit the circular
connector from the DC power supply cable to the circular chassis mount
receptacle mounted at the rear of the Model SSM.  The respective
connectors are keyed so the plug and chassis mount receptacle can fit in
only one direction.  When the connectors have been mated, rotate the
circular lock clockwise until it stops.

The following chart represents the DC voltages available at the 9 pin
circular connector on the Model PS3 power supply.



A grounding terminal is provided just below the circular power supply
receptacle on the SSM main unit, and immediately to the left of the
interface connector on the SSM expander.

The grounding terminal should be used when it is necessary to connect
the SSM and Expander to a qualified ground.  This ground terminal
should not be relied upon as a source of ground for other electronic
equipment.  The ground terminal must not be used as a substitute for the
power supplies AC grounding conductor.

In order to install the SSM in a 19" equipment rack, it will be necessary
to attach the two rack mount adapters to the main chassis of the SSM
and optional Expander.  Each rack mount adapter is attached to the main
chassis of the mixer with four 6-32 x 3/16" Phillips machine screws.

Using a Phillips screwdriver, remove the eight screws installed on both
sides of the mixer. Position the adapters so the side with the small round
holes match the threaded holes on the sides of the SSM, and the side
with the oval shaped holes are towards the front panel of the mixer.

Power supply DC pin-outs

PIN 1 - DC COMMON (AUDIO)
PIN 2 - MINUS 16.25 VDC (AUDIO)
PIN 3 -
PIN 4 -
PIN 5 -
PIN 6 - PLUS 16.25 VDC (AUDIO)
PIN 7 -
PIN 8 -
PIN 9 -

15

Rack Mount Adapters

Installation

Ground Terminal

«
...
18
19
20
21
22
...
»

Содержание SSM-24






























































Отзывы:

Нет отзывов