Speck SSM-24 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 61

Speck SSM-24 Скачать руководство пользователя страница 11

The SSM is supplied with an external rack mount power supply that is
capable of powering the Model SSM main unit and one additional
Model SSM 16 input channel expander.

The SSM requires the Model PS3-1.5 regulated power supply.

The power supply is supplied with a 6 foot, 3 conductor AC        power
cord and a 8 foot shielded DC cable. The DC cable has a circular
locking connector that insures a positive connection to the SSM.

The Model SSM and optional Expander are supplied with a set of rack
mount adapters.  If the intention is to mount the SSM in a standard 19"
equipment rack, these adapters must be mounted to the left and right
sides of the mixer.

The optional 16 channel SSM Expander is supplied with a 6' interface
harness.  This harness is required to connect the Expander to the Main
Unit.  The harness consists of high quality, shielded multiconductor
cable with 38 pin Elco connectors attached at each end.  Shorter cable
lengths are available from the factory.

The Model SSM is prewired for input expansion.  With the addition of
the 16 input Expander and its interface harness, a SSM Mixing System
may be expanded to a total of 28 positions (56 inputs).

Expanders are available in two versions: the SSMEX-32, 16 stereo
channels; and the SSMEX-16, 16 mono channels.  All input channel
functions, stereo or mono, are identical to those found on the main SSM
mixer.

The Assign 28 is an assign/subgroup module that is designed as an
output expander for the Model SSM series mixers.  The Assign 28
allows multiple sample drum sounds or multi-synth patches to be
combined and discretely bussed in a recording console fashion, but with
dedicated effects.

Standard Accessories

Regulated power supply

Interface Harness

(Expander only)

Rack Mount Adapters

Optional Accessories

SSM 16 Input Expander

Assign 28 Subgroup Module

CAUTION!

IMPORTANT!

ALWAYS CHECK THE PROPER OPERATING

VOLTAGE BEFORE OPERATING THE SSM.

USE ONLY THE POWER SUPPLY THAT IS

SPECIFIED FOR YOUR PRODUCT.

6

Chapter 1

Introduction Section

«
...
9
10
11
12
13
...
»

Содержание SSM-24






























































Отзывы:

Нет отзывов