manualshive.com logo in svg

Specac Silver Gate, Руководство пользователя

Поделиться
Скачать
Specac Silver Gate Скачать руководство пользователя страница 29

Silver Gate™ Evolution ATR System 

 

27

 
3. Take the pellet/bead or irregular shaped sample and place it very  
    carefully such that it covers as much of the surface of the ZnSe, Ge  
    or Si ATR crystal as possible. Ideally the pellet/bead sample should  
    be smooth and homogenous with no hard lumps or inclusions. This  
    will help to avoid any risk of “point load” to the ATR crystal when  
    being pressed. 
 
4. Close the bridge (

15

) and lock it to its support block (

17

) via the  

    quick lock/release screw (

18

). 

 
5. Begin turning the torque knob assembly (

16

) clockwise to lower the  

    pellet anvil (

13

) towards the sample surface. As the concave,    

    recessed surface of the pellet anvil begins to touch the pellet/bead  
    sample it will help to keep the sample centralised over the ATR  
    crystal.  
 

Note: 

Pellet/beads of 1.5mm in diameter or less are not suitable for  

          pressing using the concave recessed pellet anvil (13). 
          Small pellet/beads may have to be analysed by careful  
          manipulation using the flat stainless steel anvil(13) instead.  
          Beware to avoid any point loading on the ATR crystal with a  
          small pellet/bead sample. 

 
    Continue rotation until the white cross on the black cover at  
    the top of the torque knob assembly (

16

) ceases to rotate. At this  

    point a maximum load will be applied to the pellet/bead sample  
    forcing it against the ATR crystal. 
 

Note:

 If the sample may be hard or could produce a point load effect,  

         carry out rotation of the torque knob slowly and apply the load  
         gradually. An acceptable ATR spectrum for the sample may be  
         produced without having to apply a maximum load setting from  
         the torque knob assembly. 
 

6. Collect and record the ATR spectrum for the sample.  
 
7. To remove or change the sample, release the load/pressure on the  
    sample first by unscrewing the torque knob assembly (

16

) to retract  

Содержание Silver Gate













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды