Spearhead XRHD 250 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 40

background image

12

Spearhead XRHD

250/270/300

12. Never overload the machine and the tractor. Use the ballast if

necessary.

13. Start the machine only if all guards of the machine are fit on

proper places .

14. It is forbidden to stand in the range of operating of the machine.

15. Do not enter the working zone of the PTO shaft. It is dangerous

to approach the rotating parts of the machine.

16. Keep a safety distance from drive parts outside of the machine

(PTO shaft, hydraulic pipes).

17. Before leaving the tractor with the machine attached disconnect

the tractor, put the machine steadily on the ground (with the
hydraulic lift), apply the hand brake and if the ground is steeply
slooping, wedge the tractor.Take out the starting key.

18. Do not enter the zone between the tractor and the machine. It is

strongly forbidden to be in this zone if the tractor is not properly
disconnected, hand brake applied and starting key taken out.

3.2 Attachment on the tractor and transport

1. Before attaching the machine on or detaching it of the tractor be

sure that hydraulic lift system is in a neutral position.

2. check that a category of 3-point linkage on the tractor corresponds

to that one on the machine.

3. Be careful! There is a danger of injuries when working near or with

3-point linkage.

4. It is forbidden to be in the zone between the tractor and the

machine while working with the hydraulics.

«
...
10
11
12
13
14
...
»

Содержание XRHD 250









































Отзывы:

Нет отзывов

Похожие инструкции для XRHD 250

Бренд: Toro Страницы: 8

Бренд: Ransomes Страницы: 114

Бренд: Land Pride Страницы: 2

Бренд: Gardenline Страницы: 24

Бренд: Scag Power Equipment Страницы: 38

Бренд: Ryobi Страницы: 36

Бренд: MTD Страницы: 16

Бренд: MTD Страницы: 60

Бренд: Gude Страницы: 8

Бренд: Parkside Страницы: 52

Бренд: Yard force Страницы: 45

Бренд: MTD Страницы: 32

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 21

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды