background image

Spearhead Trident 

4000/5000/6000

 

 

 

4

 

2. 

REMEDIES AND PROCEDURES 
 

2.01.  The warranty is not effective unless the Selling Dealer registers the machine, via the Spearhead 

Machinery web site and confirms the registration to the purchaser by completing the confirmation 
form in the operator’s manual. 
 

2.02.  Any fault must be reported to an authorised Spearhead Machinery dealer as soon as it occurs. 

Continued use of a machine, after a fault has occurred, can result in further component failure for 
which Spearhead Machinery Ltd cannot be held liable. 

 
2.03.  Repairs should be undertaken within two days of the failure. Claims submitted for repairs 

undertaken more than 2 weeks after a failure has occurred, or 2 days after the parts were 
supplied will be rejected, unless the delay has been authorised by Spearhead Machinery Ltd. 

 
2.04.  All claims must be submitted, by an authorised Spearhead Machinery Service Dealer, within 30 

days of the date of repair. 

 
2.05.  Following examination of the claim and parts the manufacturer will pay, at their discretion, for any 

valid claim the cost of any parts and an appropriate labour allowance if applicable. 

 
2.06.  The submission of a claim is not a guarantee of payment. 
 
2.07.  Any decision reached by Spearhead Machinery Ltd is final. 

 

 

3. 

LIMITATION OF LIABILITY 
 

3.01.  The manufacturer disclaims any express (except as set forth herein) and implied warranties with 

respect to the goods including, but not limited to, merchantability and fitness for a particular 
purpose. 
 

3.02.  The manufacturer makes no warranty as to the design, capability, capacity or suitability for use of 

the goods. 

 
3.03.  Except as provided herein, the manufacturer shall have no liability or responsibility to the 

purchaser or any other person or entity with respect to any liability, loss, or damage caused or 
alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, 
special, consequential, or incidental damages resulting from the use or operation of the goods or 
any breach of this warranty. Notwithstanding the above limitations and warranties, the 
manufacturer’s liability hereunder for damages incurred by the purchaser or others shall not 
exceed the price of the goods. 

 
3.04.  No action arising out of any claimed breach of this warranty or transactions under this warranty 

may be brought more than one (1) year after the cause of the action has occurred. 

 

 

4. 

MISCELLANEOUS

 

 

4.01.  The manufacturer may waive compliance with any of the terms of this limited warranty, but no 

waiver of any terms shall be deemed to be a waiver of any other term. 
 

4.02.  If any provision of this limited warranty shall violate any applicable law and is held to be 

unenforceable, then the invalidity of such provision shall not invalidate any other provisions 
herein. 

 
4.03.  Applicable law may provide rights and benefits to the purchaser in addition to those provided 

herein. 

 
 
 
 
 

Содержание Trident 4000


























Отзывы: