background image

Spearhead Trident 

4000/5000/6000

 

 

 

21

 

 

 

 
PTO Shaft Maintenance & Greasing 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

 

 
 
 

 

For  maximum  life  and  performance, the  CV  body  must  be greased  regularly 
on the primary shaft.  Lubricate with the driveline in a straight position 

– up to 

30 pumps of grease may be required

 

 

 

Dismantle the metal sliding tubes, clean and re-grease to operate properly

 

 

 

Shielding  is  subject  to  damage  from  abuse  and  weathering.    Replace 

all

 

damaged components and 

all

 shielding removed during maintenance.

 

 

 

Do  not  use  PTO  adaptors  with  CV  drivelines.    Replace  special  Taper  Pin 
Bolts  only  with  genuine  OEM  parts,  periodically  check  tightness  of  nuts 
(150Nm)

 

 

 

Consult PTO Manual for additional information

 

Primary Drive 

The primary drive shaft has fitted a combined overrun and slip clutch; this should be stored in 
the dry.  After a long period of storage/use it may be necessary to disassemble the clutch to 
check its condition. 
 

  All points should be lubricated every 8 hours of use 

 

Secondary Drive 

 

 

 
 
 
 
 
 
 
 
 
 

 
 

Содержание Trident 4000


























Отзывы: