AFTER SALES SUPPORT
01904 727505 www.spearandjackson-power.com
www.spearandjackson-power.com
AFTER SALES SUPPORT
01904 727505
Please read these instructions fully before operating or maintaining your machine
SAFETY INFORMATION
Please read these instructions fully before operating or maintaining your machine
SAFETY INFORMATION
PERSONAL SAFETY
6
7
■
Only use or replace power supply cables for
this unit which correspond to the types
indicated by the manufacturer. See the
operating instructions for the order no. and
types.
■
Never touch the mains plug with wet
hands.
■
Do not run over, crush or pull the power
supply cable or extension lead, otherwise it
may be damaged. Protect the cable from
heat, oil and sharp edges.
■
The extension lead must have a cross
section in accordance with the operating
instructions and be protected against
splashed water. The connection must not
be in water.
■
Stay alert, watch what you are doing and
use common sense when operating the
machine. Do not use the machine while you
are tired or under the influence of drugs,
alcohol or medication.
■
Use personal protective equipment. shoes.
Always use eye protection. such as dust
mask, non-skid safety shoes
■
Stay alert, watch what you are doing and
use common sense when operating the
machine. Do not use the machine while you
are tired or under the influence of drugs,
alcohol or medication.
■
Prevent unintentional starting. Ensure the
switch in the off -position before connect-
ing to power source and/or battery pack,
picking up or carrying the tool.
■
Do not carry the machine with your finger
on the switch .
■
Remove any adjusting key or wrench
before turning the machine on. A wrench or
a key left attached to a rotating part of the
machine may result in personal injury.
■
Do not overreach. Keep proper footing and
balance at all times.
■
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can becaught
in moving parts.
■
If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
■
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
■
The blades continue to rotate for a few
seconds after the machine is switched off.
■
The machine is double insulated for safety
and requires no earth connection.
■
The operating voltage is 230V AC, 50Hz
(for non-EU countries 220V, 240V as
applicable). If you want to use an extension
cable when operating your product, only
the following cable dimensions should be
used:
■
1.0mm²: max. length 40m
■
1.5 mm²: max. length 60m
■
2.5 mm²: max. length 100m
■
Note: If an extension cable is used it must
be earthed and connected through the
plug to the earth cable of your supply
network in accordance with prescribed
safety regulations.
■
If in doubt contact a qualified electrician or
the after sales service.
■
WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight construc-
tion and intended for outdoor use.
■
It is recommended for increased electrical
safety to use a Residual Current Device
(RCD) with a tripping current of not more
than 30mA. Always check your RCD every
time you use it.
■
Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
■
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
■
Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
Power tool use and care
■
Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job better and
more safely when operated at the rate for
which it was designed.
■
Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
■
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk
of starting the power tool accidentally.
■
Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
raining
T
■
Read the instructions carefully. Be familiar
OPERATING SAFETY
with the controls and the proper use of the
product.
■
Never allow people unfamiliar with these
instructions or children to use the product.
