SPE EXPERT 2K-FA Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 78

SPE EXPERT 2K-FA Скачать руководство пользователя страница 4

User manual

EXPERT 2K-FA

Pag. 4 of 4 Issue 2 – May 2011

Congratulations for choosing the

SPE EXPERT 2K-FA

solid state linear amplifier: It is

small and powerful, it covers all the amateurs bands from 1.8 to 54 MHz WARC
included, completely automatically and remotable.
All operating conditions (frequency, antenna, tuner etc.) are controlled from your
transceiver. The operator has only to move the frequency tuning knob on the
transceiver.
It is possible to connect it to every type of device, it is extremely user-friendly and offers
a product which is best-in-class.

IMPORTANT

Read this instruction manual carefully before attempting to operate the linear
amplifier.
The warranty will be invalidated in the case of non-observance of these
instructions.
Keep this manual. It contains important safety and operating instructions for the
SPE EXPERT 2K-FA.

This manual may be subject to changes and updates therefore please refer
always to the updated version available on the website

www.linear-amplifier.com

.

If in doubt, refer to the English

language version.

PRECAUTIONS

Explicit definitions

WORD DEFINITION

WARNING!

Risk of danger of fire or electric shock to persons.

Possible damage to the amplifier.

NOTE:

Serious problems if not observed. Danger of fire or electric shock for the operator,
or damage to the equipment.

WARNING!

HIGH VOLTAGE! DO NOT

disconnect an antenna from the amplifier during

transmission; electric shock or fire is possible.

WARNING!

DO NOT

modify the internal wiring of the amplifier. Any modifications will invalidate the

warranty, and may reduce the performance of the linear amplifier or damage it.

WARNING!

Before

using the linear amplifier, compare the value of voltage of the local mains supply

network with the value required by the amplifier.

WARNING!

DO NOT

turn ON the linear amplifier unless it has been properly grounded through the

green/yellow conductor of the mains cord. Your dealer will already have provided the

«
...
2
3
4
5
6
...
»

Содержание EXPERT 2K-FA















































































Отзывы:

Нет отзывов