Spartus 45PFC Скачать руководство пользователя страница 5

USER’S MANUAL

EN

3

•   Power supply must never be connected 

before the accessories of SK sockets/con-

nectors are properly installed in the device.

•   Use dry and undamaged welding gloves 

and protective clothing, in order to ensure 

proper insulation of the body. It is forbidden 

to touch with a bare hand any elements that 

are parts of an electric circuit.

•   The operator must always make sure that 

there is a good electric connection of the 

return conductor to the element to be wel-

ded. The connection should be located as 

close to the welding zone as possible.

•   Maintain the electrode grip, the welding 

torch, the chassis ground clamp, welding 

cables and the welding machine in proper 

technical condition that ensures safe ope-

ration. Damaged cable insulation should be 

replaced with new insulation.

•   Never dip an electrode into water, to cool 

it down.

•   When working above the floor level (at 

a height), use a safety harness to protect 

yourself against falling, in the case of po-

tential electric shock.

•   Exercise special caution, when using the 

device in small rooms or in rooms with 

elevated humidity levels.

1.3   WELDING ARC RADIATION CAN BE 

DANGEROUS

The arc generates:
•   ultraviolet  radiation

 (can damage skin and 

eyes)

;

•   visible  light

 (can dazzle and impair vision)

;

•   infrared 

(heat)

 radiation 

(can damage skin 

and eyes)

.

Such radiation can be direct or reflected from 

surfaces such as bright metals and light colo-

ured objects.

1.3.1  Eye and face protection

•   Use welder’s helmet/shield with an appro-

priate filter to protect you face and eyes 

against sparks and welding arc radiation.

•   The shield / helmet should provide eye and 

face protection against injuries that may 

result in welding spatters.

•   Welding helmet/shield should be made in 

accordance with applicable standards. 

1.3.2  Body protection

•   The body should be protected by suitab-

le clothing in accordance with applicable 

standards. 

•   Use appropriate protective clothing made 

of durable and fire-resistant material, to 

ensure proper skin protection.

•   The use of neck protection can be necessary 

against reflected radiation. 

1.3.3   Protection of persons in the vicinity 

of an arc

•   Protect the remaining personnel present 

in the vicinity of welding works against 

negative impact of arc radiation and wel-

ding splatters. Warn them about the hazard 

resulting from exposure to the welding arc. 

  

In the vicinity of an arc, non-reflective cur-

tains or screens should be used to isolate 

persons from the arc radiation. A warning, 

e.g. a symbol for eye protection, should 

refer to the hazard of arc optical radiation.  

  

Welder’s assistants should also wear 

appropriate protective clothing.

1.4   VAPOURS AND GASES  

CAN BE DANGEROUS

Содержание 45PFC

























Отзывы: