sparkfun RedBot Скачать руководство пользователя

Страница: 38 / 39

Please see the product web page to download the example code.
http://microcontrollershop.com/product_info.php?products_id=6677

In the

Arduino IDE, select “Arduino UNO” for the board. Select COM port

for the RedBoard (this will be the number or name that appears when you

plug in the RedBoard).

WARNING:

If the MOTOR switch is set to RUN, the RedBot will move

forward (quite rapidly) for 2 seconds. You might want to pick the RedBot up

so that it doesn’t run away from you!

The RedBot will drive forward for only 2 seconds and then stop. If you want

to run the code again, you will need to press the RESET button on the

RedBot Mainboard.

What a rock star! With all that building, we bet you are ready to start

cruising. We recommend continuing to the Experiment Guide for RedBot

with Shadow Chassis to learn how to program your new robot friend.

Содержание RedBot








































Результаты поиска

Содержание RedBot

Отзывы:

Похожие инструкции для RedBot

Бренды по названию

Популярные бренды

sparkfun RedBot, Инструкция по сборке

Результаты поиска

Содержание RedBot

Отзывы:

Похожие инструкции для RedBot

Бренды по названию

Популярные бренды