sparkfun DEV-14153 Скачать руководство пользователя

Страница: 20 / 20

• BME280 Breakout Hookup Guide - For more information on the

BME280, check out this tutorial.

• Weather Meter Datasheet - Weather Meter Specifications

Need some inspiration for your next project? Check out some of these
related tutorials:

TMP006 Hookup Guide

How to get started reading
temperature with the TMP006
sensor.

HTU21D Humidity Sensor

Hookup Guide

The HTU21D humidity sensor is an
easy to use, digital, low-cost
humidity sensor.

TMP102 Digital Temperature

Sensor Hookup Guide

How to connect and use the
SparkFun Digital Temperature
Sensor Breakout - TMP102 with an
Arduino.

HIH-4030 Humidity Sensor

Hookup Guide

Measure relative humidity with
SparkFun's HIH-4030 Humidity
Sensor Breakout.

Page 20 of 20

7/10/2017

https://learn.sparkfun.com/tutorials/esp32-environment-sensor-shield-hookup-guide?_ga=2...

Содержание DEV-14153





















Результаты поиска

Содержание DEV-14153

Отзывы:

Похожие инструкции для DEV-14153

Бренды по названию

Популярные бренды

sparkfun DEV-14153, Руководство по подключению

Результаты поиска

Содержание DEV-14153

Отзывы:

Похожие инструкции для DEV-14153

Бренды по названию

Популярные бренды