manualshive.com logo in svg

Spacesaver Modular Bi-File Lateral, Руководство по установке

Поделиться
Скачать
Spacesaver Modular Bi-File Lateral Скачать руководство пользователя страница 17

17

Installation

17

Assembling Moveable Carriage Bracket

NOTE:

Each moveable carriage requires two stationary brackets and two moveable

brackets.  All four corners of a moveable carriage will require brackets.  The sta-
tionary brackets prevent the shelving from moving side to side and serve as an
In-Rail anti-tip device. 

1.

Slide the moveable bracket into the rail groove, turn it 90° degrees and then fasten
it to the center flange wheel section using pan head screws.  Fasten the stationary
bracket using a pan head screw.  Repeat on opposite side.

2.

Secure the shelving using Tek screw at one of the top two holes in the stationary
and moveable brackets.

3.

Attach the soft cover bumper over the stationary bracket rivet and then slide down
into place.  Use a pan head screw to fasten the cover at the bottom.

Stationary 

Bracket 

 (21)

550366.001

960216.001 

#10 x 5/8"  

Hex Head

Tek Screw

96116.02 

#10-24 x 1/2"  

Pan Head

Phillips

Soft Cover 

Bumper (22)

Moveable 

Bracket (23)

550363.001

960216.001 

#10 x 5/8"  

Hex Head

Tek Screw

Moveable Shelving

Step 1

Step 2

Содержание Modular Bi-File Lateral

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды