manualshive.com logo in svg

Spacesaver Modular Bi-File Lateral, Руководство по установке

Поделиться
Скачать
Spacesaver Modular Bi-File Lateral Скачать руководство пользователя страница 16

16

Installation

16

Assembling Stationary Shelving (continued)

5.

Secure the shelving in place using Tek screws at each bracket location.

6.

Place the soft cover bumper over the stationary bracket rivet and slide down into
place.  Secure cover at the bottom using pan head screw.

7.

Secure the shelving to the stationary base at each rear corner using Tek screws.

NOTE:

Floor end cover protectors are specific to the right and left floor sides.

8.

Fasten the center of the floor end cover protector to the floor section with a wood
screw.  Secure floor end cover to rail assembly using self-tapping screws at the four
outside holes of the floor end cover.  Check the fit.  Repeat on opposite side.

Stationary 

Bracket (21)

550366.001

960216.001 

#10 x 5/8"  

Hex Head

Tek Screw

960216.001 

#10 x 5/8"  

Hex Head

Tek Screw

Soft Cover 

Bumper (22)

96116.02 

#10-24 x 1/2"  

Pan Head

Phillips

Floor End

Cover Protector (15)

960180.001 

Self-Tapping Screw

#10-32 x 1/2"

96047.02 

Wood Screw 

Pan Head Phillips 

#8 x 3/4"

Содержание Modular Bi-File Lateral

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды