manualshive.com logo in svg

Spacesaver Modular Bi-File Lateral, Руководство по установке

Поделиться
Скачать
Spacesaver Modular Bi-File Lateral Скачать руководство пользователя страница 11

11

Installation

11

Assembling Stationary Bases

NOTE:

A specially designed tab and hole 

interlocking system

is used to attach many of

the following pieces.  Use a rubber or dead blow mallet to assemble.

1.

Using the interlocking system, attach a stationary end piece with two of the previously
installed stationary bases.  Tap into place with a rubber or dead blow mallet.  

2.

With all stationary bases assembled, set one stationary base end 1-9/16” from the rail
end. 

3.

Connect stationary bases using a optional spacer plate and the interlocking system.
Tap into place using a rubber or dead blow mallet.

4.

Set the cover plate between the stationary base and rail assembly.  Using self-tapping
screws, fasten the cover plate to the stationary base spacer channel. 

960180.001 

Self-Tapping Screw

#10-32 x 1/2"

Stationary Base End (7) 

Spacer Plate (8)

1-9/16"

Cover Plate (9)

Interlocking System

Tab

Hole

Содержание Modular Bi-File Lateral

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды