2
SHOCKER
CVO
WWW.
SHOCKER
PAINTBALL.COM
3
PLEASE READ CAREFULLY
PLEASE READ CAREFULLY
Assemble and install the included
barrel. Make sure The Freak
®
XL insert
is installed inside the barrel back.
Install the assembled barrel in the
front of the Shocker
®
CVO body.
Take care not to cross-thread any
barrel components during assembly
or installation, as permanent
damage may result.
The Shocker
®
CVO is equipped with
a cross bolt trigger safety. When
pressed from the left, the safety
engages to prevent the trigger from
being pulled. When pressed from
the right, exposing the red o-ring on
the left side of the grip frame, the
Shocker
®
CVO is live and ready to
fire.
The trigger safety should never
be relied upon in place of a barrel
blocker.
Carefully screw a professionally filled paintball
High Pressure Air (HPA) system into the Air
Source Adapter (ASA).
Slowly turn the ASA knob clockwise to gently
charge the Shocker
®
CVO with air.
01
BARREL
02
BARREL BLOCKER & LOADER
03
TRIGGER SAFETY
04
TURN ON AIR
05
ADJUST VELOCITY
Velocity must be measured and adjusted to below 300 feet per
second (91.4 meters per second) before each session of use.
Velocity must be tested and adjusted at the start of each paintball session. Fill the loader with paintballs and turn
it on. While wearing ASTM compliant paintball goggles in an area where all bystanders are protected, remove the
barrel blocker and fire over a chronograph to measure the velocity. Using a 5/32-inch hex key, turn velocity up
(clockwise) or down (counter-clockwise) as needed to meet the field’s standard. After each adjustment take 2 or
three shots to allow pressure to stabilize, then fire over a chronograph to check velocity. For safety and to avoid
internal damage, never adjust the Shocker
®
CVO to fire at greater than 300 feet per second.
TABLE OF CONTENTS
QUICK START - VELOCITY ADJUSTMENT
TABLE OF CONTENTS
GASSES
TRIGGER ADJUSTMENT
ADJUSTMENT/TUNING
LOADER
FEEDNECK ADJUSTMENT
QEV FORCE ADJUSTMENT
ROUTINE MAINTENANCE
BOLT
DETENTS
ASA
ADVANCED MAINTENANCE
REGULATOR
GRIP FRAME
TRIGGER
PILOT VALVE
BOLT CONTROL / QEV
TROUBLESHOOTING
PARTS GUIDE
WARRANTY
TECH SUPPORT
– THE SHOCKER
®
CVO IS NOT A TOY.
– MISUSE OF THE SHOCKER
®
CVO MAY RESULT
IN SERIOUS INJURY OR DEATH.
– EYE PROTECTION DESIGNED FOR PAINTBALL
USE MUST BE WORN BY THE USER AND ANY
PERSON WITHIN RANGE OF THE
SHOCKER
®
CVO.
– SP RECOMMENDS THAT THE SHOCKER
®
CVO
ONLY BE SOLD TO PERSONS 18 AND OLDER.
– THOROUGHLY READ THE SHOCKER
®
CVO
OPERATION AND INSTRUCTION MANUAL
BEFORE OPERATING.
CVO SPECS
OPERATING PRESSURE
PROPELLANT
OPERATION
MODES OF FIRE
ANTI-CHOP SYSTEM
BARREL THREAD
LUBRICANT
145 psi
High Pressure Air
Pneumatic
1
Low-Force Bolt
Autococker
GR33SE
TM
Turn knob slowly!
A quick pressure surge
may cause damage.
-
+
QUICK START
ON
02
03
04
05
06
06
07
08
09
10
11
14
15
16
16
18
20
39
39
CONTENTS
Install a high-performance paintball loader
in the locking feedneck. In order to
perform its at its best, the Shocker®
CVO must be consistently fed unbroken
paintballs rapidly.
Slide the included barrel blocker over the end of
the Shocker® CVO barrel. Sling the blocker’s cords
over the back of the marker and snug them tight.
The barrel blocker is a critical piece of safety
equipment and must always be used when the
Shocker
®
CVO is handled outside of an active
paintball field.
