SOYO SY-K7VIA Скачать руководство пользователя страница 22

Страница: 22 / 97

Hardware Installation

SY-K7VIA

Chapter 2

HARDWARE INSTALLATION

Congratulations on your purchase of

SY-K7VIA

Motherboard. You are

about to install and connect your new Motherboard.

Note:

Do not unpack the Motherboard from its protective anti-

static packaging until you have made the following preparations.

2-1

PREPARATIONS

Gather and prepare all the following hardware equipment to complete the

installation successfully:

Slot A processor with built-in CPU cooling fan (boxed type).

Note:

This Motherboard supports non-boxed type CPUs. The heavier

CPU cooling fan requires the installation of a CPU support stand.

DIMM memory module(s)

Computer case and chassis with adequate power supply unit

Monitor

PS/2 Keyboard

Pointing Device (PS/2 mouse)

Speaker(s) (optional)

Disk Drives: HDD, CD-ROM, Floppy drive …

External Peripherals: Printer, Plotter, and Modem (optional)

10.

Internal Peripherals: Modem and LAN cards (optional)

Содержание SY-K7VIA


































































































Результаты поиска

Содержание SY-K7VIA

Отзывы:

Похожие инструкции для SY-K7VIA

Бренды по названию

Популярные бренды

SOYO SY-K7VIA, Руководство пользователя

Результаты поиска

Содержание SY-K7VIA

Отзывы:

Похожие инструкции для SY-K7VIA

Бренды по названию

Популярные бренды