V221012
- 5 -
Flush-Mounted Series
Flush-Mount Backlight Multi-Function Controller / Flush Mount Illuminated Access Reader
Enter program mode
→
00 NNN [Node ID: 001~254; if the access controller is connected to AR-716E, its Node ID will be 001~016.]
B. Change the Node ID of Controller
Master Code modification
Enter program mode
→
09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] Set the Master code to be 876112, input
123456
→
09 876112876112
Enter the program mode
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if the Master Code is already changed= 876112, input
876112
→
program mode entered
Exit the program mode
Input
Master Code modification / Change the Node ID of Controller
A. Enter / Exit Program Mode
M4 / M6 / M8 (AR-888-H)
※
M6:
the user capacity can be 65535 because it only reads 5-digits
CARD CODE
, while in
M4/M8
it reads both
SITE CODE
and
CARD CODE
(10 digits).
Mode
Networking/
Standalone
Standalone
Networking/
Standalone
Networking/
Standalone
User
Capacity
3,000
1,500
65,535
3,000
1,500
Access Mode
M4
M6
M8
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
32
No
32
11
No
11
No
Auto-show
Duty time
Event log
Capacity
120
Holidays
Duress
Function
Time
Zone
Lift
Control
Anti-pass-
back
1.Card only
2.Card and PIN
(4-digit PIN)
+
3.User Address
(5-digit)
+ PIN
(4-digit Private PIN)
+
1.Card only
(using 17* command to set Arming PWD as 0000)
2.Card and PIN
(4-digit public PIN= Arming PWD)
+
3.Card or PIN
(4-digit public PIN= Duress code)
1.Card only
2.Card and PIN
(4-digit Private PIN)
+
3.Card or PIN
(4-digit Private PIN)
Enter program mode
→
04 N [N=4/6/8]
C.Set up M4/M6/M8
※
Confirm the access mode by assessing the beep sounds while entering the Program Mode(
M4
-4 beeps/
M6
-6 beeps/
M8
-8 beeps)
(Default
Value)
※
Default Card UID Length is 4 (Could not change by command and only be able to change by customized firmware)
(Note : The modification of controller mode between M4/M8(networking) and M6(standalone) will reset the data, user data will be required to rebuild.)
Adding and Deleting Tag
M4/M8
Add New Tags
Add by Presenting Tags (apply to Single Tag or a Batch of Tags)
※
Important Notice:
Please remember the last user address being added to make sure the old user data is not being over written with the new card in the future.
[Add single tag] Add a new tag for selected user address 100:
Enter program mode
→
19 00100 00001
→ Present the tag → Successfully added tag of user 100
[Add 2 additional tags] Add new tags to the following user address 101-102:
Enter program mode
→
19 00101 00001
→
Present (User 101) card
→
Present (User 102) card
→ Successfully added tags of user 101-102
[Add 10 additional tags] Add new tags to the following user address 103-112
Enter program mode
→
19 00103 00001
→
Present (User 103) card
→
Present (User 104) card
→
Present (...) card
→
Present (User 111) card
→
Present (User 112) card
→
Successfully added tags of user 103-112
