Sovema TDF-M EXT 180 Скачать руководство пользователя страница 18

Страница: 18 / 45

OPERATION & MAINTENANCE MANUAL

Revision 2022

_____________________________________________________________________________________

III.E - 1/2

III.E - USAGE

After having completed all safety checks and made sure the implement is parallel to the
ground, proceed as follows:

•

remove chain and pin located on front fork locking the swinging movement of arch
during transport of implement. Put such pin in free hole on top link (see fig. 1)

•

raise the implement off the ground in order to let the knives/hammers start moving
without touching ground to avoid damages

• keeping the implement raised, engage the tractor PTO at suggested engine’s revs

•

start moving the tractor forward and then gradually lower the implement

Figure 1

OPERATING TIPS

Proper ground speed for implement will depend upon the type of soil and its
conditions. However we suggest not to exceed 10 km/h (6 mph)

Lower ground speed allows to mulch with better performance. In order to obtain a opposite
result proceed more quickly

Free hole for locking pin

locking pin

chain

Содержание TDF-M EXT 180














































Результаты поиска

Содержание TDF-M EXT 180

Отзывы:

Бренды по названию

Популярные бренды

Sovema TDF-M EXT 180, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TDF-M EXT 180

Отзывы:

Бренды по названию

Популярные бренды