Sovema BTH 250 Скачать руководство пользователя страница 8

INSTRUCTION MANUAL

Page 8

Revised 2013

Make sure the PTO shaft is firmly attached to the tractor and the implement and 

that the locking pins have snapped shut.

To  connect and disconnect the PTO  shaft, please  refer to  the manufacturer’s

instruction manual and to your tractor’s instruction manual.

Connection  and  disconnection  of  the  PTO  shaft  must  be  performed  with  the

tractor’s engine turned off.

Keep hands, feet, hair and clothing away from moving parts

To  prevent  injury  by  thrown  objects  DO  NOT  operate  unless  all  personnel,

livestock and pets are 20 m (65 ft) away.

The rotating  parts  of the  machine  have  been designed  and  tested  for  rugged

use. However they can fail upon impact with heavy solid objects. Such impact

can cause fragments to be thrown outward at very high speed. To reduce the

possibility  of  serious  injury,  or  even  death,  never  allow  the  rotating  parts  to

contact such obstacles.

Stop the machine and tractor immediately upon hitting an obstruction. Turn off

the engine,  remove the key,  inspect  and  repair any  damage before  resuming

operation.

No repairs or adjustments should be attempted while the machine is attached to

a tractor that is turned on

.

Disengage tractor PTO and place transmission into neutral before attempting to

start engine.

TRANSPORT SAFETY

Plan  your route to avoid heavy traffic.

For public roads, comply with state and local safety and movement rules.

Be sure that the implement is in the raised position for transport.

When you must drive, do not drink.

Pay attention to traffic when operating near or crossing roadways.

Reduce  speed  when  transporting  mounted  implement  to  avoid  bouncing  and

loss of steering control.

MAINTENANCE SAFETY

Good maintenance is your responsibility. Poor maintenance is an invitation to 

trouble.

Please follow these common practices:

-

keep service area clean;

-

make sure the area is well lit;

-

make sure the tools and the electric appliances are properly grounded;

-

make sure the service area is properly ventilated.

Содержание BTH 250






































Отзывы: