background image

ATTACHING THE HAND-HOLDS:

 

 

 

Attach  the  hand-holds  by  using  the  appropriate  length  socket  head  bolt  through  the  hole  in  the  hand-hold  into  the 
threaded holes in the panel and tighten with the hex wrench provided.  These may be placed to suit the activities and 
skill level of the users.  

 

 

Check  carefully  inside  the  hole  of  each 
hold to see if there is a washer present 
in  order  to  select  the  proper  bolt 

(see 

picture  at  left)

.  Place the bolt in the 

hold, through the wall, and into the t-nut.  
Tighten  with  an  allen  wrench  until  the 
hold  is  snug  and  does  not  spin.    Use 
caution as over tightening may result in 
hold  breakage,  especially  with  smaller 
holds.   

 

 

The  hand-holds  are  color  coded  to 
make  instruction  easier  and  to  help  de-
sign  climbing  “routes”  by  order  of  diffi-
culty.  The  GREEN 

 

handholds are the  

easiest.    YELLOW  is  intermediate,  and  RED    is  the  most    challenging.    The  orientation  of  the  handholds  can  also 
make a difference - an easy handhold, turned sideways or upside down, may become more difficult.  This allows for a 
tremendous number of different motor planning challenges.  Adjust them however it fits your situation.  You can even 
keep a “map” of your handholds by client, so they can gauge their progress over the same route.

 

 
LOCKING THE PANELS IN THE VERTICAL POSITION:

 

 

 

The panels can be used in a vertical position, or the bottom will slide out to a sloped position for clients who lack suffi-
cient strength to hold on to a vertical surface.  

Note: the panels are locked in the vertical position with two 3/8 x 1-3/4” 

flat head screws in the middle panel (see figure 4).  These screws must be in place and engage the locking 
nuts on the inside channel when using the panels in the vertical position.  Failure to observe this could result 
in injury if the panel were to slide out while in use.  

 

 

To use the panels in the sloped configuration, remove the two screws, grasp the bottom panel and slide it out.  The 
panels will roll on the wheels and stop in the proper position.  

Always make sure that the panels are pulled completely 

out  before  using  in  the  sloped  configuration.   

Put the two bolts that were removed in a safe place out of the 

reach of clients. 

 

MAINTENANCE CHECKLIST: 

All of the following wear points should be checked as indicated and recorded on the checklist enclosed. 
 

 

Weekly: 

 

All hand-holds MUST be checked and tightened on a daily or weekly basis, depending on the frequency of 
use.  These holds WILL loosen with frequent use and with changes in humidity. 

 

Check the bolts holding the wood panels to the strut system on a weekly basis.  Tighten when necessary. 

 
 

Monthly: 

 

On a monthly basis, the lag screws holding the horizontal strut pieces to the wall should be checked for tight-
ness, and tightened if loose.  Likewise, the bolts holding the upright strut pieces to the horizontal strut 
should be checked and tightened if necessary.  You will have to remove the wooden climbing surfaces in or-
der to check this. 

 

Check the wheels to see that they roll freely.  Remove any lint or hair that may be clogging it.  Check that the 
“axle” of the wheel is tight.  Tighten if necessary 

 

Check the shoulder bolt of the slide mechanism at the top of the strut pieces.  If the shoulder bolts are loose, 
tighten before continuing use. 

 

Check for cracked or broken hand-holds.  In the unlikely event that one breaks or cracks, discontinue use 
immediately 

 

Check the wood surface and edges for splinters.  If found, discontinue use until repaired.  You may repair it 
by sanding the area smooth with a medium grit sandpaper, and applying two coats of clear lacquer to the re-
paired area. 

 

Correct bolt usage: 
 

Holds with washer 

  Holds without washer 

Each bolt only needs to clear the back of the hold by 3/4” max. 

Содержание 110010



























Отзывы: