background image

Instruction Sheet

 

Convertible Climbing Wall - Block/Brick Wall  110010 

Store these instructions with the enclosed maintenance checklist 
in a safe place.  You may also access them on our website.

 

Take time to familiarize yourself with the use and maintenance of this equipment before using.  Please file this 
Instruction Sheet in an accessible location:  the Instruction Sheet must be read and familiar to anyone who is 
using Southpaw Enterprises Equipment.   

IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping.   
If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. 

 
Caution should be used at all times when using this equipment.  It is imperative that clients be under constant 
supervision while climbing.  Mats of appropriate thickness should be used.  A client’s strength, skills, and abili-
ties must be taken into consideration when determining how closely to spot him or her.  Some clients will re-
quire  almost  constant,  hands-on  support,  while  others  may  be  able  to  climb  completely  without  assistance.  
You, as the therapist, must make this decision based on your knowledge of the client’s skills and aptitude.  Do 
not have more than one client on the wall at a time unless proper supervision can be administered for each cli-
ent.  Failure to take these things into consideration increases risk of mishap or injury.  
 
 
MATERIALS LIST: 

 

 

 

 

 

TOOLS NEEDED: 

 

 

 

 

 
  3 - 29” X 57” Wood Panels 

 

  3 - 1-5/8” x 13/16” x 50-1/4” Slotted Channels   

 

Drill and 7/8” masonry drill bit 

  2 - Upright Assemblies  

 

 

 

 

7/32” and 5/16” Hex Allen Wrenches 

20 - Hand-holds with attachment bolts   

 

 

Tape Measure 

  1 - Hardware Package                 

 

 

 

Pencil  or Marker 

  1 - Instruction Sheet   

 

 

 

 

Level 

  1 - Maintenance Checklist 

 

 

 

 

Step Ladder 

 

TWO PEOPLE REQQUIRED FOR ASSEMBLY 
 
WEIGHT LIMIT: 300 LBS. 
 
ATTACHING HORIZONTAL CHANNEL TO WALL (Figure 1): 

 

 

Once location has been determined for climbing wall, measure up from the floor and make a mark at 23”, 67”, and 
83”.  Using a level, draw a line between the outside edges where horizontal channel will be placed.  Drill a  pilot hole 
into the wall at each point for the screws, approximately 16” apart.

 

 

Place the channel against the wall with the open side facing out to make sure that the slotted holes in the channel 
line up with the holes drilled in the wall.

 

 

Put a 5/16” washer on a lag bolt.  Because the 1-3/8” washers are too large to simply place it into the strut, you will 
need to slide it into the end of the channel and line it up with one of the end slots.  Line up the end slot/washer with 
the far-left, bottom pilot  hole.  Put the lag bolt  w/ 5/16” washer through the big  washer and the channel (from the 
open side of the channel) into the pilot hole.  Screw the lag bolt into the pilot hole, but do not tighten all the way.  
Repeat on the opposite end of the channel, then in the two center slots using a 5/16” and an 1-3/8” washer on each 
bolt.  Now, tighten the lag bolts while holding the center of the channel on the horizontal line.  Repeat this operation 
on the remaining two lines.

 

Содержание 110010



























Отзывы: