background image

Questions? Call Toll Free at 1-800-737-2112

 

 

Copyright © 2009 MAT Engine Technologies, LLC

RESPONSIBILITY OF OPERATOR

1. Carefully read and follow these safety instructions.  Failure to do so can result in serious injury.
2. Know your product.  Read and understand this manual before use.  Compare the illustrations to unit.  Learn location  
 

and function of all controls.  Thoroughly understanding the unit before use will result in the best performance and safety.

3. Follow all instructions when assembling the unit.  If the unit was purchased in assembled condition, the operator must  
  check the unit carefully to make sure it was assembled according the instructions in the manual before use.
4. Regularly inspect the tiller.  Make sure parts are not bent, damaged, or loose.
5. Use this equipment for its intended purpose only.
6. Operate the unit only with guards, shields, and other safety items in place and working correctly.
7. Service the unit only with authorized or approved replacement parts.
8. Complete all unit maintenance and adjustments according to the instruction in this manual.

WARNING

Look for this symbol to point out important safety precautions. It means: “ Attention! Become Alert!  Your Safety Is 
Involved.”

WARNING

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State 
of California to cause cancer and birth defects or other reproductive harm.  

WARNING

To prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug 
wire and put wire where it cannot contact the spark plug.

PREPARATION SAFETY

WARNING

  Read, understand, and follow all instructions on the machine and in this manual. Be thoroughly familiar with the 

  controls and the proper use of the tiller before starting. Know how to stop the engine quickly.

  Familiarize yourself with all the safety and operating decals on this equipment.

WARNING

  Thoroughly inspect the area where the tiller is to be used and remove all foreign objects. Your equipment can propel  

  small objects at high speed causing personal injury or property damage.  Stay away from breakable objects, such as  
  house windows, auto glass, greenhouses, etc.

  Check that all nuts and bolts are tight and equipment is in good condition before each use.  

WARNING

  Always check that the flameout wire is connected before starting engine.

OPERATION SAFETY

  Never allow children or young teenagers to operate the tiller.

  

WARNING

  Keep area of operation clear of all bystanders, particularly small children and pets.

  Only allow responsible individuals, who are familiar with the instructions, to operate the tiller. 

 

WARNING

  Do not operate the 

tiller while under the influence of alcohol, drugs, or other medication which can cause drowsiness  

  or affect your ability to operate this machine safely.

  Do not use this machine if you are mentally or physically unable to operate the machine safely.

  Always wear ANSI compliant safety goggles or safety glasses with side shields when operating tiller to protect your  

  eyes from foreign objects, which can be thrown from the unit.

Important Safety Information 

• Save all instructions 

Important 

Safety 

Information

 

2

 

Содержание S-RTT-196MD





















































Отзывы: