background image

TILTING AND STATIONARY  

ELECTRIC SELF CONTAINED 

STEAM KETTLES 

LIMITED WARRANTY 

Southbend warrants that the equipment, as supplied by the factory to the original purchasers, is free from defects in materials and workmanship. 
Should any part thereof become defective as a result of normal use within the period and limits defined below, then at the option of Southbend such 
parts will be repaired or replaced by Southbend or its Authorized Service Agency. This warranty is subject to the following conditions:

 

If upon inspection by Southbend or its Authorized Service Agency it is determined that this equipment has not been used in an appropriate manner, 
has been modified, has not been properly maintained, or has been subject to misuse or misapplication, neglect, abuse, accident, damage during 
transit or delivery, fire, flood, riot or Act of God, then this warranty shall be void.

 

Specifically excluded under this warranty are claims relating to installation; examples are improper utility connections and improper utilities supply. 
Claims relating to normal care and maintenance are also excluded; examples are calibration of controls, and adjustments to pilots and burners.

 

Equipment failure caused by inadequate water quality is not covered under the warranty. WATER QUALITY must not exceed the following limits; 
Total Dissolved Solids (TDS) - 60 PPM (Parts Per Million), Hardness - 2 Grains or 35 PPM, PH Factor - 7.0 to 7.5. Water pressure 30 PSI 
minimum, 60 PSI Maximum. Boiler maintenance is the responsibility of the owner and is not covered by warranty.

 

This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.

 

Repairs under this warranty are to be performed only by a Southbend Authorized Service Agency. Southbend can not be responsible for charges 
incurred from other than Authorized Southbend Agencies.

 

THIS WARRANTY MUST BE SHOWN TO AN AUTHORIZED SERVICE AGENCY WHEN REQUESTING IN-WARRANTY SERVICE WORK. THE 
AUTHORIZED SERVICE AGENCY MAY AT HIS OPTION REQUIRE PROOF OF PURCHASE DATE.

 

This warranty does not cover services performed at overtime or premium labor rates nor does Southbend assume any liability for extended delays 
in replacing or repairing any items in the equipment beyond the control of Southbend. "Southbend shall not be liable for consequential or special 
damages of any nature that may arise in connection with such product or part." Should service be required at times which normally involve overtime 
or premium labor rates, the owner shall be charged for the difference between normal service rates and such premium rates.

 

In all circumstances, a maximum of one hundred miles in travel and two and one half hours (2.5) travel time shall be allowable. In all cases the 
closest Southbend Authorized Agency must be used.

 

The actual warranty time periods and exceptions are as follows:

 

This warranty only covers product shipped into the 48 Contiguous United States and Hawaii, one year labor, one year parts effective from the date 
of original purchase. There will be no labor coverage for equipment located on any island not connected by roadway to the mainland.

 

Exceptions to standard warranty, effective within above limitations:

 

Glass Windows, Door Gaskets, Rubber Seals, Light Bulbs, Ceramic Bricks,

 

Sight Glasses, Cathodic Descalers or Anodes .................................................................................................................... 90 days material and labor.

 

Stainless Steel Fry Pot  ................................................................................................. 4 years extended material warranty on fry pot only - No labor.

 

Stainless Steel Open Top Burners  ............................................................................. 4 years extended material warranty on burners only - No labor.

 

Pressure Steam Boiler Shell ................................................................................. Prorated 4 years extended warranty on boiler shell only - No labor.

 

(Boiler shells which have not been properly maintained will not be covered by warranty.)

 

In all cases parts covered by a five year warranty will be shipped FOB the factory after the first year.

 

Our warranty on all replacement parts which are replaced in the field by our Authorized Service Agencies will be limited to three months on labor, 
six months on materials (parts) effective from the date of installation. See LIMITED WARRANTY - REPLACEMENT PARTS for conditions and 
limitations.

 

If the equipment has been changed, altered, modified, or repaired by other than a qualified service technician during or after the one year limited 
warranty period, then the manufacturer shall not be liable for any damages to any person or to any property which may result from the use of the 
equipment thereafter.

 

"THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABILITY OR FITNESS, AND CONSTITUTES THE ENTIRE LIABILITY OF SOUTHBEND. IN NO EVENT DOES THE 
LIMITED WARRANTY EXTEND BEYOND THE DURATION OF ONE YEAR FROM THE EFFECTIVE DATE OF SAID WARRANTY."

 

SOUTHBEND - Effective February 1, 1990

 

 

TILTING & STATIONARY ELECTRIC STEAM KETTLES

 

SECTION TWO - USER'S GUIDE

 

PAGE 1

 

 

Содержание KSLE-20



























Отзывы: