Sound Skulptor EQ573 Скачать руководство пользователя | Manualshive

Страница: 3 / 10

background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 01/05/14

EQ573 Assembly guide – Main board

10. Relays

Add RLY1 and RLY2.

11. Electrolytic capacitors

Add C19 to C23, C76, C77, C82, C83, C85, C90, C91, C93 to C96.
Solder one lead first, adjust verticality then solder the second lead.

Warning

: The +lead must go into the +hole. Do not reverse (they may explode !)

12. Inductors

It is necessary to leave a small gap between the inductors and the PCB surface in order to avoid any
electrical contact between the metal parts and pads. Fit a piece of double sided adhesive tape (supplied
with the kit) on the inductor, between the pins. It is not necessary to remove the second protective

layer from the tape as it is only used as a spacer.

Solder L1 and L2.

Copyright ©2011 to today SoundSkulptor

«
1
2
3
4
5
...
»

Содержание EQ573











Отзывы:

Нет отзывов

Похожие инструкции для EQ573

Бренд: AeroAudio Страницы: 8

Бренд: Tek'it Audio Страницы: 39

Бренд: JBL Страницы: 7

Бренд: Rane Страницы: 8

Бренд: Cambridge Audio Страницы: 13

Бренд: Jensen Страницы: 27

Бренд: Extron electronics Страницы: 2

Бренд: Boss Audio Systems Страницы: 7

Бренд: Emerson Страницы: 29

Бренд: Emerson Страницы: 34

Бренд: Emerson Страницы: 43

Бренд: Emerson Страницы: 34

Бренд: Emerson Страницы: 42

Бренд: Emerson Страницы: 34

Бренд: Emerson Страницы: 24

Бренд: Emerson Страницы: 26

Бренд: Emerson Страницы: 24

Бренд: Emerson Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды