Sound Skulptor EQ573 Скачать руководство пользователя | Manualshive

Страница: 10 / 10

background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 01/05/14

EQ573 Assembly guide – Link cable assembly (for connecting to MP573)

3. Cable soldering

Insert the cable 3 wires from beneath the PCB into the 3 unplated
holes, red in centre, yellow on the “Y” side. Insert the red and
yellow wire tips into the corresponding PCB holes and solder.
Cut the shield cable to the good length, flatten it on the
rectangular pad and solder.
Repeat for the other side of the cable.

Copyright ©2011 to today SoundSkulptor

«
...
8
9
10

Содержание EQ573











Отзывы:

Нет отзывов

Похожие инструкции для EQ573

Бренд: Panasonic Страницы: 2

Бренд: Boss Audio Systems Страницы: 12

Wireless music system for iPod

Бренд: Brookstone Страницы: 14

Бренд: Curtis Страницы: 11

Бренд: Kenwood Страницы: 36

Бренд: Kenwood Страницы: 30

Бренд: E-Bench Страницы: 22

Бренд: Philips Страницы: 26

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды