background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 01/05/14

EQ573 Assembly guide

Safety warning

The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the 
realisation of a kit unless he has full knowledge about safely handling main powered devices.

Please read the “DIY guide” before beginning.

Print or open the following documents :

EQ573 Schematics

EQ573 Components layout

EQ573 Parts list

EQ573 Setup guide

Follow this guide from item number 1 till the end, in this order. The assembly order is based on components height, from 
low to high profile, in order to ease the soldering process : The component you are soldering is always taller than the 
previously assembled ones and it is pressing nicely against the work area foam.

EQ573 Assembly guide – Main board

1. Diodes

Add D1 to D5. Use a lead forming tool to bend the leads at 0.4”.

Warning

 : Make sure to respect the direction of the diodes which is marked by a ring on the component 

and a double line on the PCB marking.

2. Resistors

Add R17 to R66.

Control the resistor values with a digital multimeter. Bend the leads at 0.4” with a lead forming tool.

3. Test pins

Solder the 5 test pins TP1 to TP5.

4. Ceramic capacitors

Add C79, C87.

5. Film capacitors

Add C24 to C49, C51, C53 to C55, C57 to C75, C80, C81, C84, C88, C89, C92.

Copyright ©2011 to today SoundSkulptor

Содержание EQ573











Отзывы: