Sound Devices Kashmir MIXPRE-3 II страница 82 Скачать руководство пользователя

Страница: 82 / 84

User Guide

Devices, LLC product, even if Sound Devices, LLC has been advised of the possibility of such damages. In

any case, Sound Devices, LLC’s entire liability under any provision of this evaluation license shall be limited

to the greater of the amount actually paid by you for the SOFTWARE PRODUCT or U.S. $5.00. Because some

states/jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damag

es, the above limitation may not apply to you.

Governing Law

This agreement and limited warranty are governed by the laws of the state of Wisconsin.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. FCC Part 15.19 (a) (3)

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter

ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC and ISED RF Exposure SAR limits exposure limits for general population /

uncontrolled exposure.

Cet appareil est conforme à la norme FCC et USED RF Exposure SAR limite les limites d’exposition pour la

population générale / l’exposition incontrôlée.

This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the

following two conditions: 1) this device may not cause interference, and 2) this device must accept any in

terference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada, exempts de licence standard RSS (s). Son fonctionne-

ment est soumis aux deux conditions suivantes: 1) ce dispositif ne peut pas causer d’interférences, et 2)

ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais

fonctionnement de l’appareil.

DRAFT

Not For Publication

Содержание Kashmir MIXPRE-3 II





















































































Результаты поиска

Содержание Kashmir MIXPRE-3 II

Отзывы:

Похожие инструкции для Kashmir MIXPRE-3 II

Бренды по названию

Популярные бренды

Sound Devices Kashmir MIXPRE-3 II, Руководство пользователя

Результаты поиска

Содержание Kashmir MIXPRE-3 II

Отзывы:

Похожие инструкции для Kashmir MIXPRE-3 II

Бренды по названию

Популярные бренды