WARNING:
Over tightening can damage the stove or canister valve which may cause fuel to leak.
Always check for leaks after installing the fuel canister. Do not light the stove if a leak
is detected. Keep stove and fuel out of the reach of children.
Never cover the stove and/or canister with a windscreen, rock or similar item which
may cause "overheating". Additionally, do not use the stove near another stove in
use, an open fire, or any other heat source. If the stove overheats, it could damage
the product and endanger your safety.
WARNING:
Gas canister must be changed or dismounted in a well-ventilated location, preferably
outside, away from other people and any sources of ignition, such as naked flames,
pilot flames, electric heaters/equipment.
CAUTION:
Do not attempt to touch the appliance when hot. Wait until it is completely cooled off
before touching.
WARNING:
Check that O-rings between the appliance and the gas container are in place and in
good condition before connecting the gas canister. Do not use this appliance if it has
damaged or worn O-rings. If there is a leak from this appliance (smell of gas) and the
gas flow cannot be stopped, move the appliance to a well-ventilated location,
preferably outside, away from any ignition source.
1. Turn the flame control handle clockwise to
the OFF position to completely shut off the
gas feed .
2. Carefully screw the threaded section on
the bottom of the stove assembly into the
threaded part of the canister. Tighten
slightly firm but do not over-tighten.
Mounting the Stove
After Using the Stove
To extinguish the flame, turn control handle clockwise until it stops.
After the stove has cooled completely, stow all 4 (four) pot supports by unhooking each
pot support from the hooks. Never touch the stove while it is hot. Touching the stove
while hot may result in burning and/or bodily injuries.
When unfolding pot supports, gently adjust each pot support slightly toward the right.
Stowing:
Flame
control handle
Piezo
ignition button
Canister
Pot support
Ignition unit
Burner
Burner crown
Electrode
(OFF)
(ON)
WARNING:
Do not move the appliance during operation. Never
leave a burning or hot stove unattended.
CAUTION:
Accessible parts may be very hot.
Using the Stove
1. Carefully open the valve by turning the control
handle counterclockwise (about 3/4turns) until you
hear the sound of fuel escaping. Then press the
Piezo ignition button quickly to light the stove.
2. If the stove does not immediately ignite, close the
valve by turning the control handle fully clockwise.
Wait a few seconds and repeat the first step.
3. Once the appliance is lit, regulate the intensity of
the flame with the control handle. Turn
counterclockwise for stronger flame. Turn
clockwise toward - for weaker flame. The stove
should produce a steady, blue flame.
Do not be concerned if the stove makes a high-pitched whistling sound when in use.
This is not a defect in the stove. Atmospheric pressure, air temperature, humidity, etc.
cause this to occur from time-to-time.
Weaker flame
Stronger flame
(OFF)
Lift each pot support gently as shown in illustrations #1 and #2. Gently press each pot
support to the left while the pot support is being lifted. Secure the opening on the pot
support to the hook on the outer wall of the burner head.
Setting the pot-support:
#1
#2
Toward left
CAUTIONS:
Be sure to secure all pot supports firmly on the
hooks located on the outer wall of the burner head.
Failure to observe this instruction may cause
sudden dropping of the pot support that may result
in damage to property and/or bodily injuries.
Pot support
Hook hole
Hook
Extinguishing the Flame
CAUTION:
Do not over tighten the valve system by
force. Over-tightening may result in damage
to the valve system.
Unscrew the stove from the canister.
Place the stove and pot support in the
included case for storage.
Push
"Click"
If the hinge of the pot support becomes
hard to turn, apply a small amount of
lubricant oil to the hinge. Wipe off any
excess lubricant oil.
