Sony XDCAM PDW-1500, Руководство по эксплуатации

Страница: 107 / 154

Ch
apt
er 8
Men
u
s
107
8-2 Basic Setup Menu
1
Press the MENU button.
The menu appears in the time data display.
2
Press the RESET button.
The message “Init setup?” appears in the time data
display.
To abandon operations and return to the setup
menu display
Press the RESET button again.
3
Press the SET button.
The menu settings are reset to their factory default
settings.
Switching between 525(U) line, 525(J) line
and 625 line modes (menu item 013)
To switch between 525(U) line, 525(J) line and 625 line
operation modes, proceed as follows.
1
Press the MENU button.
2
Turn the jog dial or shuttle dial to display menu item
013 in the time data display.
3
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to set menu item 013 to “on.”
4
Press the SET button.
5
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to select the line mode 525(U), 525(J) or
625.
6
Press the SET button.
7
Turn the unit off (press the on/standby switch to put
the unit in the standby state).
Next time the unit is turned on (when the unit is put in the
operating state by pressing the on/standby switch), it
operates in the new mode.
Menu bank operations (menu items B01 to
B13)
This unit allows menu settings to be saved in what are
termed “menu banks.” Saved sets of menu settings can be
recalled for use as required.
To jump to menu item B01
You can recall any required menu by turning the jog dial
or shuttle dial after pressing the MENU button.
If you press the MENU button first, then the COUNTER
SELECT button, you can jump directly to menu item B01
or H01. The recalled menu item toggles between B01 and
H01 every time you press the COUNTER SELECT button.
Saving the current active menu settings
Set one of basic menu items B11 “SAVE SETUP BANK-
1” to B13 “SAVE SETUP BANK-3” to “on,” depending
on which of the menu banks you wish to save in, then press
the SET button.
Recalling settings from a menu bank
Set one of basic menu items B01 “RECALL SETUP
BANK-1” to B03 “RECALL SETUP BANK-3” to “on,”
depending on which of the menu banks you wish to recall
from, then press the SET button.
To recall menu bank 4, select “bank-4” under menu item
B20 “RESET SETUP MENU.”
1)
1) This is supported from firmware version 1.4.
Refer to the maintenance manual for more information
about menu bank 4.
REC
VARIABLE
PRESET
PB
L
MIX
R
MONITOR
NETWORK
LOCAL
REMOTE
ACCESS
PHONES
TOP
F REV F FWD
END
PREV NEXT PLAY
AUDIO
MONITOR SEL METER SEL INPUT CH INPUT SEL
VIDEO
INPUT SEL
COUNTER
SELECT
SUB
CLIP
THUMB
NAIL SET RESET
SHIFT
EJECT
HOLD
STOP REC
SH
UTT
LE
JOG VAR
MARK1
ESSENCE
MARK
CLIP
MENU
S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER
dB
-12
-20
-30
-40
-60
0
CH- 15
SG DATA
ANA SDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH- 26
SG DATA
ANA SDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH- 37
SG DATA
ANA SDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH- 48
SG DATA
ANA SDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU VITC VITC COUNTER REC INH VIUB
EDIT KEY INH REMOTE [9P iLINK]
INPUT
i.LINK
SDI
1/2
5/6
3/4
7/8
625
525
IMX[50 40 30]
DVCAM 4 8 CH 18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR
AUDIO
SYS MENU
MENU
1 2
3