Sony WEGA KV-32XBR450, Руководство по обслуживанию

Страница: 7 / 31

KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
— 23 —
Control Register
Function & Link
Data
Type
Data
Range
Note
P&P-Left
(M)-DRC
P&P-Left
(M)-1080i
P&P-Left
(M)-DRC
P&P-Left
(M)-480i
0 YLEV Y-Out gain 0~63 23 27* 28 31*
1 CLEV Cb&Cr-Out gains 0~63 17 55* 32 31*
2 SCON Sub contrast
Adj.
0~15
3 SCOL Sub color
Adj.
0~15
4 SHUE Sub hue Adj. 0~15
5 YDLY Y/C delay time 0~3
SNNR Data-related Settings UHF/VHF CVideo SVideo
YPbPr
480i
SNNR=0
(-offset)
SNNR=1
(-offset)
SNNR=2
(-offset)
SNNR=3
(-offset)
6 SHAP Sharpness 0~15 6 4 4 4 0 1 2 3
7 SHF0 Sharpness f0 selector 0~3 0 0 0 0
8 PREO Sharpness pre/over-shoot ratio 0~3 3 0 0 0
9 BPF0 Chroma band filter f0 setting 0~3 3 0 0 0
10 BPFQ Chroma band filter Q setting 0~3 0 3 3 3
11 BPSW Chroma band filter on/off 0, 1 1 0 0 0
12 TRAP Y bolck chroma trap filter on/off 0, 1 0 0 0 0
13 LPF YPbPr-Output LPF on/off 0, 1 0 0 0 0
UHF/VHF Video
YPbPr
480i
14 AFCG AFC Loop Gain (PLL between Hsync & HVCO) 0, 1 1 0 0
15 CDMD V countdown system mode selector 0~3 3 3 3
16 SSMD H&Vsync slide level setting 0~3 0 0 0
17 HMSK Masking of macrovision signal on/off 0, 1 1 1 1
18 HALI H automatic adjustment on/off 0, 1 0 0 0
19 PPHA H TIM phase adjustment for video 0~15 7 7 7
P&P-Left
(M)-DRC
P&P-Left
(M)-1080i
P&P-Left
(M)-DRC
P&P-Left
(M)-480i
Cb-Offset1 of Cb IN (Pin34)
Cb-Offset2 of EXT Cb (Pin38)
Cr-Offset1 of Cr IN (Pin35)
Cr-Offset2 of EXT Cr (Pin39)
Single
UBLK = 0 UBLK = 1 UBLK = 2 UBLK = 3 UBLK = 4 UBLK = 5UBLK = 6 UBLK = 7 UBLK = 0~7
22 ATPD Auto-pedestal Inflection Point 0~3 0
1 2 3
1 2 3 2 0
23 DCTR DC Transmission Ratio 0~3 0
1 1 1
2 2 2 3 0
Adj.: Adjusted data
[Adj.-2steps]: The adjusted data - 2 steps
CVideo: CVideo1~4 Inputs
SVideo: SVideo1~3 Inputs
*: Settings not used
(31): The center setting = 31
UHF/VHF
7 [7]
31* 31 31* 31
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
31*
7 [7]
Data Initial/Average Setting
(32V&36V CRTs)
Video: CVideo1~4 & SVideo1~3 Inputs
P&P-Left (M)-1080i&480i: If P&P-Left is
1080i/480p signal, the signal from the main
chroma decoder is sent to MID/VDO input.
*: Settings not used
31* 0~(31)~63
YPbPr-480i
UHF/VHF & Video
7 [Adj.-2steps]
UHF/VHF & Video
0
Video
7 [7]
7 [7]
7 [Adj.-2steps]
0
P&P & Favorite
CBOF 31 31
CROF 0~(31)~63
YPbPr-480i
P&P & Favorite
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
20
21
Register
No & Name
Data Initial Setting & [Average Data]
(32V&36V CRTs)
DX1A-2001&2000 SERVICE LIST (#2-1):
CXA2103-1 {Main}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3048 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA)
Slave Address: 9Ah { Main }