Sony SVT-RA168 Скачать руководство пользователя страница 17

Страница: 17 / 100

2-1

SVT-RA40/RA168

1. Maintaining and Checking the Mechanism

1-1. Regular Checks and Maintenance Items

To obtain full function and maximum performance from the set, and to stop it getting dirty or scratched,

we recommend that you carry out the following maintenance procedures and regular checks. The mainte-

nance checks described in the following section should also be carried out without fail after carrying out

any repairs to the set.

Note: Oil and Grease

Always use the specified brands of oil and grease. If you use a grease with the wrong viscosity, for

example, this can lead to all sorts of problems. Be careful to keep the oil and grease free of dust and

foreign bodies.

A “drop” of oil is the amount of oil remaining on the tip of a rod with a diameter of 1. 5 mm after it is

dipped in oil to a depth of 1 cm and then taken out.

Section 2

Mechanical Adjustments

Содержание SVT-RA168





































































































Результаты поиска

Содержание SVT-RA168

Отзывы:

Бренды по названию

Популярные бренды

Sony SVT-RA168, Руководство по обслуживанию

Результаты поиска

Содержание SVT-RA168

Отзывы:

Бренды по названию

Популярные бренды