manualshive.com logo in svg

Sony SVT-RA168, Руководство по обслуживанию

Поделиться
Скачать
Sony SVT-RA168 Скачать руководство пользователя страница 15

1-5

SVT-RA40/RA168

1-4. Installation of the Front Panel

When installing the front panel to the chassis after repaires

and adjustments.

1.

Pressing down the door opener lever of the mechanism

main unit.

2.

Set the cassette door to half-opened state as shown in

Fig. 1-1-5, and install the front panel to the chassis.

n

Opened cassette door position does not install the front

panel to the chassis.

Fig. 1-1-5

1-3. Temporarily Setting Up and

Connecting CP-1 PWB Assembly

The following is an example of how to place and connect

the main board without a jig, when repairing the CP-1

PWB assembly.

1.

Place the mechanism unit and main board up side

down as a whole on a flat surface with foil side of the

main board facing up.

2.

Operete the unit using the buttons on TM-1 PWB and

TM-2 PWB.

Fig. 1-1-4

PW-1 PWB

Screws 

CP-1 PWB Assembly (Foil side)

TM-1 PWB

Mechanism 
Main Unit

 Terminal Board

Cassette Compartment

TM-2 PWB

Jutted part of 
Cassette Holder

Door Opener Lever

Front Panel

Cassette Door

(Position B)

Cassette Door

(Position A)

Содержание SVT-RA168





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды