1-1
8
Unpacking
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR:
Note
• The supplied remote commander is for the exclusive use of this DVD-VCR.
• Remote commander
• Aerial cable
• R6 (size AA) batteries
• Audio cord
(pinplug ×2
y
pinplug ×2)
• Video cord
(pinplug ×1
y
pinplug ×1)
Check your model name
The instructions in this manual are for the 3 models: SLV-D940P AZ, SLV-D940P ME and
SLV-D940P EA. Check your model name by looking at the rear panel of your DVD-VCR.
SLV-D940P AZ is the model used for illustration purposes. Any difference in operation is
clearly indicated in the text, for example, “SLV-D940P AZ only.”
Getti
ng Sta
rted
9
Setting up the remote commander
Step 2 : Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
may cause a malfunction.
Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this DVD-
VCR and a Sony TV. Buttons on
the remote commander marked
with a dot (•) can be used to
operate your Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
To operate
Set TV / DVD·VIDEO to
the DVD player
DVD·VIDEO, then press SELECT DVD and point at the remote sensor at
the DVD-VCR
the VCR
DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor
at the DVD-VCR
your TV
TV and point at the remote sensor at your TV
TV /
DVD·VIDEO
Remote sensor
SELECT
VIDEO
SELECT
DVD
continued
10
Setting up the remote commander
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
Now you can use the
?
/
1
, VOL +/–, PROG +/–, MUTING*, TV/VIDEO, 0-9 and
-/--* buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
* for Sony TV only
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
1
Set TV / DVD·VIDEO at the top of the remote commander to TV.
2
Hold down
?
/
1
, and enter your TV’s code number using the number buttons.
Then release
?
/
1
.
Manufacturer
Code number
Sony
01, 02
Akai
68
Ferguson
52
Grundig
10, 11
Hitachi
24
JVC
33
Loewe
45
Mivar
09, 70
NEC
66
Nokia
15, 16, 69
Panasonic
17, 49
Philips
06, 07, 08
Saba
12, 13
Samsung
22, 23
Sanyo
25
Sharp
29
Telefunken
36
Thomson
43
Toshiba
38
Manufacturer
Code number
Getti
ng Sta
rted
11
Connecting the DVD-VCR
Step 3 : Connecting the DVD-VCR
Note that “Advanced Hookups” (page 54) explains additional hookup methods that
will optimize the picture and sound for a true “hometheatre” experience.
Note
• When you connect the DVD-VCR and your TV only with an aerial cable, you have to tune
your TV to the DVD-VCR (see page 13).
1
Disconnect the aerial cable from your TV
and connect it to on the rear panel of the
DVD-VCR.
2
Connect
of the DVD-VCR and the
aerial input of your TV using the supplied
aerial cable.
3
Connect the mains lead to the mains.
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
continued
1. GENERAL
This section is extracted from instruction manual.
(2-109-228-11)
SLV-D940P AZ/D940P EA/D940P ME
Содержание SLV-D940P AZ
