Sony RM-PJM50, Руководство пользователя

Страница: 23 / 178

1-15
VPL-FX50
28
(GB)
;;;;;;;;
;;;;;;;;
;;;;;;;;
;;;;;;;;
;;;;;;;;
a
x
b
c
a: Distance between the screen and the center of the lens
b: Distance from the floor to the center of the lens
c: Distance from the floor to the foot of the projector
x: Free
Screen size (inches) 40 60 80 100 120 150 180 200 250 300
Minimum
1490 2280 3060 3850 4630 5810 6980 7770 9730 11690
a
(58 3 /
4
) (89 7 /
8
) (120 1 /
2
) (151 5 /
8
) (182 3 /
8
) (228 7 /
8
) (274 7 /
8
) (306) (383 1 /
8
) (460 3 /
8
)
Maximum
1820 2780 3740 4700 5660 7100 8540 9500 11900 14300
(71 3 /
4
) (109 1 /
2
) (147 3 /
8
) (185 1 /
8
) (222 7 /
8
) (279 5 /
8
) (336 3 /
8
) (374 1 /
8
) (468 5 /
8
) (563 1 /
8
)
b
Minimum
x–305 x–457 x–610 x–762 x–914 x–1143 x–1372 x–1524 x–1905 x–2286
(x–12 1 /
8
) (x–18) (x–24 1 /
8
) (x–30) (x–36) (x–45) (x–54 1 /
8
) (x–60) (x–75 1 /
8
) (x–90 1 /
8
)
Maximum x
c
Minimum
x–415 x–567 x–720 x–872 x–1024 x–1253 x–1482 x–1634 x–2015 x–2396
(x–16
3
/
8
) (x–22
3
/
8
) (x–28
3
/
8
) (x–34
3
/
8
) (x–40
3
/
8
) (x–49
3
/
8
) (x–58
3
/
8
) (x–64
3
/
8
) (x–79
11
/
32
) (x–94
3
/
8
)
Maximum x–100 (x–4)
Unit: mm (inches)
Center of the lens
Center of the screen
Wall
Floor
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS
×
50.127/1.3102) – 73.9}
×
1.025
a (maximum) = {(SS
×
64.519/1.3102) – 107.9}
×
0.975
b (minimum) = x – (SS/1.3102
×
9.984)
c (minimum) = x – (SS/1.3102
×
9.984 + 110)
Distance between the
front of the cabinet and
the center of the lens
Standard lens:
30.5 mm (1
1 /
4
inches)
Installation Example
Installation Example
29
(GB)
Notes for Installation
Unsuitable Installation
Do not install the projector in the following situations.
These installations may cause malfunction or damage
to the projector.
Poorly ventilated
• Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on surfaces
(rugs, blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.
When the internal heat builds up due to the block-up,
the temperature sensor will function with the
message “High temp.! Lamp off in 1 min.” The
power will be turned off automatically after one
minute.
• Leave space of more than 50 cm (19 3 /
4
inches)
around the unit.
• Be careful that the ventilation holes may inhale
tininess such as a piece of paper.
• If you put something in front of the front ventilation
holes, the exhaust may be inhaled into the projector
through the ventilation holes at the bottom, causing
the internal temperature to rise, which activates the
protection circuit. Install the projector so that the
exhaust is not blocked.
Highly heated and humid
• Avoid installing the unit in a location where the
temperature or humidity is very high, or temperature
is very low.
• To avoid moisture condensation, do not install the
unit in a location where the temperature may rise
rapidly.
Very dusty
Avoid installing the unit in a location where there is a
lot of dust; otherwise, the air filter will be obstructed.
The dust blocking the air through the filter may cause
raising the internal heat of the projector. Clean it up
periodically.
Unsuitable Conditions for Use
Do not do any of the following.
Blocking the ventilation holes
Avoid using something to cover over the ventilation
holes; otherwise, the internal heat may build up.
Tilting right/left
Avoid using as the unit tilts more than 20 degrees. Do
not install the unit other than on the floor or ceiling.
These installations may cause malfunction.
The front to back tilt angle of this projector is not
limited.
20°
Notes for Installation
Installation