Sony RDR-HX715 - Dvd Recorder & Hard Disk Drive Combo Скачать руководство пользователя страница 11

Страница: 11 / 142

1-5

Step 4: Connecting the Audio Cords

Select one of the following patterns

, according to the input jack on your TV monitor, projector,

or AV amplifier (receiver). This will enable you to listen to sound.

Connecting to audio L/R (left/right) input jacks

This connection will use your TV’s or stereo amplifier’s (receiver’s) two speakers for sound. You can
enjoy the following surround effects (page 61).
• TV: Dynamic, Wide, Night
• Stereo amplifier (receiver): Standard, Night

Connecting to a digital audio input jack

If your AV amplifier (receiver) has a Dolby

Digital or DTS

decoder and a digital input jack, use this

connection. You can enjoy Dolby Digital (5.1ch) and DTS (5.1ch) surround effects.

* The yellow plug is used for video signals (page 18).

VIDEO

AUDIO

INPUT

VHF/UHF

AC IN

COMPONENT

VIDEO OUT

VIDEO S VIDEO

R-AUDIO-L

OUT

COMPONENT

VIDEO IN

DIGITAL OUT

SET TOP

BOX

CONTROL

G-LINK

COAXIAL

OPTICAL

PCM/DTS/
DOLBY DIGITAL

LINE OUT

VIDEO S VIDEO

R-AUDIO-L

LINE IN

HDMI OUT

DIGITAL OUT

COAXIAL

OPTICAL

PCM/DTS/
DOLBY DIGITAL

VIDEO S VIDEO

R-AUDIO-L

LINE OUT

HDMI OUT

AV amplifier (receiver)
with a decoder

(red)

TV, projector, or AV
amplifier (receiver)

Audio/video cord
(supplied)

: Signal flow

Coaxial digital cord (not supplied)

to DIGITAL OUT (COAXIAL or OPTICAL)

to LINE OUT (R-AUDIO-L) 1 or 2

Optical digital cord (not supplied)

Rear (L)

DVD recorder

(white)

(yellow)

(white)

(red)

[Speakers]

Front (L)

[Speakers]

to coaxial or
optical/HDMI
digital input

Rear (R)

Front (R)

Subwoofer

Center

HDMI cord
(not supplied)

ook

up
s

and

tti

Hint

For correct speaker location, see the operating
instructions supplied with the connected components.

Notes

• Do not connect your TV’s audio output jacks to the

LINE IN (R-AUDIO-L) jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.

• In the connection

, do not connect the LINE IN (R-

AUDIO-L) and LINE OUT (R-AUDIO-L) jacks to
your TV’s audio output jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.

• In the connection

, after you have completed the

connection, make the appropriate settings under
“Audio Connection” in “Easy Setup” (page 25).
Otherwise, no sound or a loud noise will come from
your speakers.

• With the connection

, the surround sound effects of

this recorder cannot be used.

• When you connect the recorder to an AV amplifer

(receiver) using an HDMI cord, you will need to do one
of the following:
– Connect the AV amplifier (receiver) to the TV with

the HDMI cord.

– Connect the recorder to the TV with a video cord

other than HDMI cord (component video cord,
S VIDEO cord, or audio/video cord).

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.

Step 5: Connecting the
Power Cord

Connect the supplied power cord to the AC IN
terminal of the recorder. Then plug the recorder
and TV power cords into an AC outlet. After you
connect the power cord,

you must wait for a

short while before operating the recorder.

You can operate the recorder once the front panel
display lights up and the recorder enters standby
mode.
If you connect additional equipment to this
recorder (page 28), be sure to connect the power
cord only after all connections are complete.

AC IN

to AC outlet

to AC IN

Step 6: Preparing the
Remote

You can control the recorder using the supplied
remote. Insert two size AA (R6) batteries by
matching the

and

ends on the batteries to the

markings inside the battery compartment. When
using the remote, point it at the remote sensor

on the recorder.

Notes

• If the supplied remote interferes your other Sony DVD

recorder or player, change the command mode number
for this recorder (page 24).

• Use the batteries correctly to avoid possible leakage

and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or

batteries of different manufacturers.

– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an extended

period of time, remove the batteries.

– If battery leakage occurs, wipe out any liquid inside

the battery compartment, and insert new batteries.

• Do not expose the remote sensor (marked

on the

front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.

You can adjust the remote’s signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.

Notes

• Depending on the connected unit, you may not be able

to control your TV or AV amplifier (receiver) with
some or all of the buttons below.

• If you enter a new code number, the code number

previously entered will be erased.

• When you replace the batteries of the remote, the code

number may be reset to the default setting. Set the
appropriate code number again.

Slide the TV/DVD switch to TV.

Hold down

[

Enter your TV’s manufacturer code (see
“Code numbers of controllable TVs”
below) using the number buttons.

Controlling TVs with the remote