Sony MDS-JA333ES - Md Player Скачать руководство пользователя страница 29

Страница: 29 / 95

5-5. Creating Continuos Recorded Disc

• This disc is used in focus bias adjustment and error rate check.

The following describes how to create a continuos recording disc.

1. Load a disc (blank disc) commercially available.

the disc is loaded by pushing the tray.

2. Rotate the

AMS

knob and display “CREC 1MODE”

(C35).

3. Press the YES button to display “CMEC 1MID”.

“CREC1 (0300)” is displayed for a moment and recording starts.

4. Complete recording within 5 minutes.
5. Press the MENU/NO button to stop recording.
6. Press the

button to eject the disc.

The above has been how to create a continuos recording data for
the focus bias adjustment and error rate check.
Note:
• Be careful not to apply vibration during continuos recording.

5-6. Check before Repairing

This check aims at locating the approximate position of cause of
trouble before starting to replace parts using specifications.
For detailed information, refer to [Checks before Part Replacement
and Adjustment] of Service note.

5-6-1. Temperature Compensation Offset Check

Before adjustment, set the internal temperature and the ambient
temperature are between 22 and 28

Checking procedure:
1. Rotate the

AMS

knob to display “TEMP CHECK”

(C12).

2. Press the YES button.
3. It is OK when “T=@@(##)[OK” appears. It is NG when

“T=@@(##)[NG” appears. (@@ is the current value. ## is the
value that is written in the non-volatile memory.)

5-6-2. Laser Power Check
Before check:

• Refer to Section 1 “Service note” How to open the disc tray when

power switch is turned off, and laser power check.

• Check the IOP value of optical pick-up. (Refer to Section 5-8

“Recording and displaying the IOP information”.)

Connection:

Checking procedure:

1. Insert the laser power meter from the disc inlet and set it on the

objective lens of the optical pick-up. (When it cannot be set
properly, press the

button and

button to move the

optical pick-up.)
Connect the digital voltmeter to CN110

-pin (I+3V) and the

CN110

-pin (IOP).

2. Rotate the

AMS

knob to display “LDPWR CHECK”

(C13).

3. Press the YES button once to display “LD 0.9mW $ ”.

Confirm that the reading of the laser power meter is 0.84 to
0.92 mW.

4. Press the YES button once again to display “LD 7.0mW $ ”.

Confirm that the readings of the laser power meter and digital
bolt meter satisfy the specified value.

5. Then press the YES button once again to display “LD

6.2mW $ ”.

Specification:
Laser power meter reading: 7.0 ± 0.2 mW
Digital bolt meter reading: Optical pick-up displayed value ± 10 %

6. Press the MENU/NO button to display “LDPWR CHECK”

(C13) and stop laser emission.
(The MENU/NO button is effective at all times to stop the
laser emission.)

Note 1

: After step 4, the display of “LD 0.7mW$ ” “LD

6.2mW$ ”, “LD Wp $ ” is switched every
time when pressing the YES button. Operation is not
necessary for these displays.

Laser power meter

Optical pick-up

objective lens

Digital voltmeter

CN110

-pin (I+3V)

CN110

-pin (IOP)

BD board

KMS

260B

24391

H0528

(For the checking procedure of
this value, refer to Section 5-8
“Recording and displaying the
IOP information”.)

IOP = 52.8 mA in this case
IOP (mA) = digital bolt meter reading (mV)/1 (W)

(Optical pick-up label)

Содержание MDS-JA333ES - Md Player
































































































Результаты поиска

Содержание MDS-JA333ES - Md Player

Отзывы:

Бренды по названию

Популярные бренды

Sony MDS-JA333ES - Md Player, Руководство по обслуживанию

Результаты поиска

Содержание MDS-JA333ES - Md Player

Отзывы:

Бренды по названию

Популярные бренды