HCD-MX700Ni/MX750Ni
2
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classi
fi
ed as
a CLASS 1 LASER product.
This marking is located on the
rear exterior.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
μ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
• PARTY STREAMING and PARTY STREAMING logo are trademarks of Sony Corporation.
• VAIO and VAIO Media are registered trademarks of Sony Corporation.
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thom-
son.
• Microsoft, Windows, Windows Vista, Windows 7™, Windows Media are trademarks or regis-
tered trademarks of Microsoft Corporation in the United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
• iPhone is a trademark of Apple Inc.
• “Made for iPod” and “Works with iPhone” means that an electronic accessory has been designed
to connect speci
fi
cally to iPod or iPhone, respectively, and has been certi
fi
ed by the developer to
meet Apple performance standards.
• Apple is not responsible for the operation of this device or its compliance with safety and regula-
tory standards.
• “
” is a mark of the Wi-Fi Alliance.
• DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certi
fi
ca-
tion marks of the Digital Living Network Alliance.
• Wake-on-LAN is a trademark of International Business Machines Corporation in the United
States.
• This product is protected by certain intellectual property rights of Microsoft Corporation. Use
or distribution of such technology outside of this product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
• The system names and product names indicated in this manual are generally the trademarks or
registered trademarks of the manufacturer.
• In this manual, Microsoft Windows XP Home Edition, Microsoft Windows XP Professional and
Microsoft Windows XP Media Center Edition are referred to as Windows XP.
• In this manual, Microsoft Windows Vista Home Basic, Microsoft Windows Vista Home Pre-
mium, Microsoft Windows Vista Business and Microsoft Windows Vista Ultimate are referred
to as Windows Vista.
• In this manual, Microsoft Windows 7 Starter, Microsoft Windows 7 Home Premium, Microsoft
Windows 7 Professional, Microsoft Windows 7 Ultimate are referred to as Windows 7.
• ™ and ® marks are omitted in this manual.
Содержание HCD-MX700Ni
Страница 81: ...MEMO HCD MX700Ni MX750Ni 81 ...
