SECTION 4
TEST MODE
4-1. PRECAUTIONS FOR USE OF TEST MODE
1. As loading related operations will be performed regardless of
the test mode operations being performed, be sure to check that
the disc is stopped before setting and removing it. Even if
the
§
(MD) button is pressed while the disc is rotating during
continuous playback, continuous recording, etc., the disc will
not stop rotating. Therefore, it will be ejected while rotating.
Be sure to press the
§
(MD) button after pressing
the
^
(CD) button and the rotation of disc is stopped.
2. The erasing-protection tab is not detected in the test mode.
Therefore, operating in the recording laser emission mode and
pressing the
r
REC button, the recorded contents will be
erased regardless of the position of the tab. When using a disc
that is not to be erased in the test mode, be careful not to enter
the continuous recording mode and traverse adjustment mode.
But “CREC MODE”, “EF MO CHECK” and “EF MO AD-
JUST” is detect the erasing-protection tab and recording laser
power off.
4-1-1.
Recording Laser Emission Mode and Operating
Button
1. Continuous recording mode (CREC MODE)
2. Traverse adjustment mode (EF MO ADJUST)
3. Laser power adjustment mode (LDPWR ADJUST)
4. Laser power check mode (LDPWR CHECK)
5. When pressing the
r
REC button.
6. Traverse checking mode (EF MO CHECK)
4-2. SETTING THE TEST MODE
With the power supply to the set in OFF (standby) status, while
pressing the PLAY MODE button and
^
(MD) button simul-
taneously, then release the button.
4-3. RELEASING THE TEST MODE
Press the REPEAT button, and the power is turned OFF (standby
status), and the set becomes ready for normal operation.
4-4. BASIC OPERATIONS OF THE TEST MODE
All operations are performed using the VOLUME knob button,
p
(CD) button, and
^
(CD) button. The functions of these
buttons and knob are as follows.
Table 4-1.
4-5. SELECTING THE TEST MODE
Thirteen test modes are selected by turn VOLUME.
Table 4-2.
• For detailed description of each adjustment mode, refer to the “5.
ELECTRICAL ADJUSTMENTS”.
• If a different adjustment mode has been selected by mistake, press
the
^
(CD) button to exit from it.
*1: The EEP MODE, Scurve CHECK, MANUAL CMD VERIFY
MODE, SLED MODE, ACCESS MODE, 0920 CHECK,
WRITE sure?, HEAD ADJUST and SVDATA READ are not
used in servicing. If set accidentally, press the
^
(CD) but-
ton immediately to exit it.
Display
Contents
TEMP CHECK
Temperature compensation offset check
LDPWR CHECK
Laser power check
EF MO CHECK
Traverse (E-F balance) check
EF CD CHECK
Travers (Pre mastered disk) check
FBIAS CHECK
Focus bias check
CPLAY MODE
Continous playback mode
CREC MODE
Continous recording mode
Scurve CHECK
S-curve check (*1)
VERIFY MODE
Non-volatile memory check (*1)
DETRK CHECK
Detrack check
TEMP ADJUST
Temperature compensation offset adjustment
LDPWR ADJUST
Laser power adjustment
EF MO ADJUST
Traverse (E-F balance) adjustment
EF CD ADJUST
Traverse (Pre mastered disk) adjustment
FBIAS ADJUST
Focus bias adjustment
EEP MODE
Non-volatile memory mode (*1)
MANUAL CMD
Manual command transfer mode (*1)
SVDATA READ
Data reading out mode (*1)
ERR DP MODE
Operation of error histories memory
SLED MOVE
Operation of sled moter (*1)
ACCESS MODE
Access check (*1)
0920 CHECK
Outermost periphery check (*1)
WRITE sure?
Non-volatile memory initialize
HEAD ADJUST
HEAD adjustment check (*1)
CPLAY2MODE
Continous playback mode
CREC2MODE
Continous recording mode
Function
Proceeds onto the next step.
Finalizes input.
Returns to previous step.
Stops operations.
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
