HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
– 19 –
CD SECTION
Note:
1. CD Block is basically constructed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M
Ω
impedance.
4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the following
checks.
S Curve Check
Procedure :
1. Connect the oscilloscope to test points TP (FE) and TP (VC).
2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of
the BD board with lead wires.
3. Press the
1
/
u
button to turn the set ON.
4. With the disc (YEDS-18) loaded, press the
·P
button and
perform focus search. (Focus search will be performed in the
same way even while the disc table is pushed in and out.)
5. Check the symmetry and peak to peak level of the oscilloscope
waveform (S curve) at this time.
S-curve waveform
6. After check, remove the lead wire connected in step 2.
Note:
• Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.
RF Level Check
Procedure :
1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD
board.
2. Press the
1
/
u
button to turn the set ON.
3. Put disc (YEDS-18) in and playback 5 track.
4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
Note:
Clear RF signal waveform means that the shape “
◊
” can be
clearly distinguished at the center of the waveform.
RF signal waveform
Adjustment Location :
[ BD BOARD ] — SIDE A —
SECTION 7
DIAGRAMS
7-1. CIRCUIT BOARDS LOCATION
– 20 –
Procedure:
1. Connect oscilloscope to test point TP (TE) on BD board.
2. Press the
1
/
u
button to turn the unit ON.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the
· P
button.
5. Check the level B of the oscilloscope's waveform and
the A (DC voltage) of the center of the Traverse wave-
form.
Confirm the following:
• A/B x 100 = less then ± 22 (%)
• B = 1.3 ± 0.6 Vp-p
1 track jump waveform
E-F Balance (1 Track Jump) check
oscilloscope
BD board
TP (FE)
TP (VC)
+
–
symmetry
A
B
Within 3
±
1 Vp-p
oscilloscope
BD board
TP (RF)
TP (VC)
+
–
VOLT/DIV : 200mV
TIME/DIV : 500ns
level : 1.45
±
0.25 Vp-p
TUNER UNIT
JACK board
TC-B board
TC-A board
PANEL FL board
PANEL VR board
FRONT INPUT board
TRANS board
SUB TRANS board
(W300/W5000/XB500)
MAIN board
PA board
CD-L board
CD-R board
LED (PANEL) board
DOOR SWITCH board
BD board
LED (CD) board
CD MOTOR board
TABLE SENSOR board
AUDIO board
LEAF SW board
0V
Center of the waveform
B
Symmetry
A (DC voitage)
level : 1.3
±
0.6 Vp-p
oscilloscope
BD board
TP (TE)
TP (VC)
+
–
TP
(VC)
TP
(RF)
TP
(TE)
TP
(FE1)
TP (FE)
TP
(AGCCON)
Содержание HCD-DR4
Страница 2: ... 2 ...
Страница 36: ...HCD DR4 DR5 DR6 DR440 W300 W5000 XB500 53 54 7 11 SCHEMATIC DIAGRAM DECK SECTION Page 49 ...
Страница 52: ...HCD DR4 DR5 DR6 DR440 W300 W5000 XB500 85 86 7 27 SCHEMATIC DIAGRAM CD MOTOR SECTION Page 48 ...
Страница 54: ...HCD DR4 DR5 DR6 DR440 W300 W5000 XB500 89 90 7 29 SCHEMATIC DIAGRAM JACK SECTION Page 57 65 Page 52 ...