Sony Handycam DCR-TRV11, Руководство по обслуживанию

Страница: 130 / 215

5-15
5. B Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. or 3. Initializing the B
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. or 4. Modification of B
Page Data”.)
Table. 5-1-6.
Address Remark
00
01 to 16
17
18
19
1A to 20
21
22 to 4F
50
51 to 53
54
55 to 5D
5E
5F
60 to 6F
70
71 to FF
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
(Modified data. Copy the data built in the same
model.)
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
1-2-3. INITIALIZATION OF E, F, 7 PAGE DATA
1. Initializing the E, F, 7 Page Data
Note1: If “Initializing the E, F, 7 Page Data” is performed, all data of the
E page, F page and 7 page will be initialized. (It is impossible to
initialize a single page.)
Note2: If the E, F, 7 page data has been initialized, following adjustments
need to be performed again.
1) Modification of E, F, 7 page data
2) Camera system adjustments
3) IR transmitter adjustments
Adjusting page F
Adjusting Address 10 to FF
Adjusting page E
Adjusting Address 00 to FF
Adjusting page 7
Adjusting Address DCR-TRV6/TRV6E/TRV11/TRV11E:
00 to 59
DCR-TRV20/TRV20E:
00 to A3 (Note3)
00 to B5 (Note4)
Note3:
Camera microprocessor ver. 1.0
Note4: Camera microprocessor ver. 2.0 or later
Switch setting:
POWER .................................................................. CAMERA
Initializing Method:
1)
Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 01, and set the following data and press
the PAUSE button.
2D: DCR-TRV6/TRV11/TRV20 (NTSC)
2F: DCR-TRV6E/TRV11E/TRV20E (PAL)
3) Select page: 6, address: 03, set data: 01, and press the PAUSE
button.
4) Select page: 6, address: 02, and check that the data changes to
“01”.
5) Perform “Modification of E, F, 7 Page Data”.
2. Modification of E, F, 7 Page Data
If the E, F, 7 page data has been initialized, change the data of the
“Fixed data-2” address shown in the following table by manual input.
Version check of the camera microprocessor:
1)
The data of page: 6, address: FF shows the version of the camera
microprocessor (VC-240/241 board IC802).
Modifying Method:
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of E, F, 7 Page data
1)
Turn off the power and turn on again.
Data
01
02
Version
1.0
2.0
Ver 1.1 2000. 06