Sony FilmStation UP-DF550, Руководство пользователя

Страница: 35 / 58

Mis
c
e
llan
eous
Precautions
35
Miscellaneous
Precautions
Safety
• Operate the unit using the power source specified in
“Specifications” (on page 38).
• Be careful not to damage the AC power cord by
placing or dropping heavy objects on it; it is dangerous
to use the unit with a damaged AC power cord.
• If you do not intend to use the unit for a long time,
disconnect the AC power cord.
• Unplug the AC power cord by grasping the plug, not
the cable itself.
• Do not disassemble the unit.
• Do not remove the cabinet. There is a danger of
electric shock from the internal parts.
• Be careful not to spill water or other liquids on the
unit, or to allow combustible or metallic material to
enter the cabinet. If used with foreign matter in the
cabinet, the unit is liable to fail, or present a risk of fire
or electric shock.
• If the unit malfunctions or if a foreign body falls into
the cabinet, disconnect the power immediately and
consult your Sony dealer.
Installation
Avoid placing the unit in a location subject to:
– mechanical vibration
– high humidity
– excessive dust
– direct or excessive sunlight
– extremely high or low temperatures
Ventilation holes are provided to prevent the unit
from overheating. Be careful not to obstruct them
with other units or by covering the unit with a cloth
etc.
Condensation
• If the unit is subjected to wide and sudden changes in
temperature, such as when it is moved from a cold
room to a warm room or when it is left in a room with
a heater that tends to produce large amounts of
moisture, condensation may form inside the printer. In
such cases the printer will probably not work properly,
and may even develop a fault if you persist in using it.
If moisture condensation forms, turn off the power and
allow the printer to stand for at least one hour.
• If the film is subjected to wide and sudden changes in
temperature, condensation may form on the film in the
film tray. This will cause the printer to malfunction.
Also, if the film is used in this state, spots are likely to
appear on the printout.
• To store a half-used package of film, replace the film
in its original packing and reseal the package. If
possible, before using sealed film, place it, in its
sealed package, in a warm room for several hours.
Doing so prevents condensation from forming when
the film is removed from its package.
Transporting the Unit
Before transporting the unit, remove the supplied
accessories and then put them back into their original
packing. Transporting the unit with the supplied
accessories still installed may cause malfunctions.
Note
If you move the unit with the casters for placing the unit
vertically (sold separately) attached, the unit may topple
and cause injury. Do not use the caster to move the unit.
Cleaning the Cabinet
Note
Before you clean the printer, be sure to press the 1 ON/
STANDBY switch to enter the standby state and then
remove the power plug.
When the cabinet becomes dirty
When solvents such as benzene or thinner, or acid,
alkaline or abrasive detergent, or chemical cleaning
cloths are used on the printer surface, the surface finish
may be damaged. Take care with respect to the
following:
• Clean the printer surface with a 50 to 70 v/v%
concentration of isopropyl alcohol or a 76.9 to 81.4 v/
v% concentration of ethanol.
• Stubborn stains may be removed with a soft cloth such
as a cleaning cloth lightly dampened with mild
detergent solution and then clean using the above
chemical solution.
• Do not use unnecessary force to rub the printer surface
with a stained cloth. The printer surface may be
scratched.
• Do not keep the printer surface in contact with a
rubber or vinyl resin product for a long period of time.
The surface finish may deteriorate or the coating may
come off.
Maintenance
Perform the following maintenance regularly after every
500 printings.