6-1
SECTION 6
TEST MODE
DVP-S9000ES
6-1.
GENERAL DESCRIPTION
The Test Mode allows you to make diagnosis and adjustment eas-
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
6-2.
STARTING TEST MODE
Press
[TITLE]
,
[CLEAR]
,
[POWER]
buttons on the remote com-
mander in this order with the power of main unit in OFF status,
and the Test Mode starts, then the menu shown below will be dis-
played on the TV screen. At the bottom of menu screen, the model
name and revision number are displayed.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the POWER button.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Version Information
6. Video Level Adjustment
7. Prog Level Adjustment
Exit: Power Key
_
Model
: DPX13xx
Revision
: 1.xxx
6-3.
SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press
[0]
key on the remote com-
mander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. ROM, Model, Region
3. RAM, EEPROM, NFLASH, H2GA
4. Servo, ARP
5. AV Decoder
6. OSD
7. FBI, SACD
8. Video
9. Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1. All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 ROM, Model, Region
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
[ ]
key to go to the next item, or
[ ]
key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press
[ ]
or
[ENTER]
key.
If an error occurred, the diagnosis is suspended and the error code
is displayed as shown below.
### Syscon Diagnosis ###
3-3. EEPROM Write/Read
Error 03: EEPROM Write/Read N
Address
: 00000001
Write Data : 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press
[ ]
key to quit the diagnosis, or
[ ]
key to repeat the
same item where an error occurred, or
[ ]
key to continue the
check from the item next to faulty item.
Subnemu
Selecting 2 and subsequent items calls the submenu screen of each
item.
For example, if “2. ROM, Model, Region” is selected, the follow-
ing submenu will be displayed.
### Syscon Diagnosis ###
Check Menu
No. 2 ROM, Model, Region
0. Quit
1. All
2. ROM Revision
3. ROM Check Sum
4. Model Type
5. Region
_
0. Quit
Quit the submenu and return to the main menu.
1. All
All submenu items continuous check
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
>
.
x
>
.
x
