18
DISPLAY 0
<[BACK]>
Ver. xxxxxx
Node unique ID
Root Yes (No)
Forceroot
B. Rst [xxx]
G.C [xx]
Async [xxx]
State BR
Note IDR
Split THR
Split TLR
Bus TR
Busy TR
Babndwidth AR
Channel AHR
Channel ALR
Output MPR
Output PCR
Input MPR
Input PCR
Config ROM
LINK IC [00]
LINK IC [04]
LINK IC [08]
LINK IC [0C]
LINK IC [10]
LINK IC [14]
LINK IC [18]
LINK IC [1C]
LINK IC [20]
LINK IC [24]
LINK IC [28]
LINK IC [2C]
LINK IC [30]
LINK IC [34]
LINK IC [38]
LINK IC [3C]
LINK IC [40]
4-4. i.LINK TEST MODE
Not used service
Not used service
A bus reset is generation if
signals cannot be transmitted as
a result of failed connector or
cable connections.
Not used service
The counter is incremented
whenever a command is
received from another unit.
A ping signal should be
transmitted from another unit to
check to make sure that the
counter has been incremented
and that commands may be
received properly.
Not used service
DISPLAY “0”, “1”, and “2” will be displayed each time the DISPLAY button is pressed and the command will then be executed.
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
DISPLAY 1
0000 zzzzzzzz
0008 zzzzzzzz
0018 zzzzzzzz
001C zzzzzzzz
0204 zzzzzzzz
0210 zzzzzzzz
0220 zzzzzzzz
0224 zzzzzzzz
0228 zzzzzzzz
0900 zzzzzzzz
0904 zzzzzzzz
0980 zzzzzzzz
0984 zzzzzzzz
0000 zzzzzzzz
0004 zzzzzzzz
0008 zzzzzzzz
000C zzzzzzzz
0010 zzzzzzzz
0014 zzzzzzzz
0018 zzzzzzzz
001C zzzzzzzz
0020 zzzzzzzz
0024 zzzzzzzz
0028 zzzzzzzz
002C zzzzzzzz
0030 zzzzzzzz
0034 zzzzzzzz
0038 zzzzzzzz
003C zzzzzzzz
0040 zzzzzzzz
DISPLAY 2
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
Description
The display mode will change every time
the DISPLAY button is pressed.
Firmware version
Display firmware update number
Display Node unique ID
Display root
Bus reset
Pressing the REC MODE button will be executed
Bus reset counter
Display total number of times bus has
been reset
Pressing the DISPLAY button resets the
counter to zero.
Gap count
Display current gap count
ASYNC packet reception counter
Display the total number of ASYNC
packets (excluding ACK) received so far.
Pressing the DISPLAY button resets this
counter to zero.
State Bits Resister
Display register values
Pressing the DISPLAY button causes
the following items to be displayed in
succession each time the button is
pressed:
A: Register name
B: Offset address register value
Node ID Register
Split Timeout High Register
Split Timeout Low Register
Bus Time Register
Busy Timeout Register
Bandwidth Available Register
Channel Available Hi Register
Channel Available Low Register
Output Master Plug Register
Output Plug Control Register
Input Master Plug Register
Input Plug Control Register
Config ROM
LINK IC Register [00]
LINK IC Register [04]
LINK IC Register [08]
LINK IC Register [0C]
LINK IC Register [10]
LINK IC Register [14]
LINK IC Register [18]
LINK IC Register [1C]
LINK IC Register [20]
LINK IC Register [24]
LINK IC Register [28]
LINK IC Register [2C]
LINK IC Register [30]
LINK IC Register [34]
LINK IC Register [38]
LINK IC Register [3C]
LINK IC Register [40]
Note
D>i.LINK check
Содержание CDP-LSA1
Страница 22: ...22 Adjustment Location BD BOARD SIDE B TP FE TP TE TP VC TP XPCK TP RFAC IC103 30 16 15 1 ...
Страница 30: ...CDP LSA1 30 30 6 7 SCHEMATIC DIAGRAM MAIN 1 3 SECTION See page 28 for Printed Wiring Board ...
Страница 35: ...CDP LSA1 35 35 6 11 SCHEMATIC DIAGRAM PANEL SECTION See page 33 for Waveforms ...
Страница 37: ...CDP LSA1 37 37 6 13 SCHEMATIC DIAGRAM POWER SECTION ...
