Sony BVP-E10 Series, Руководство по эксплуатации товара

Страница: 71 / 204

71 Chapter 7 Location and Function of Parts and Controls
BVP-E10 Series Product Information Manual
7-5-2 Rear Panel
a a a a
CAMERA connector (triax connector)
Connect a BVP-E10-series Color Video Camera using
a triax cable. All of the signals of the BVP-E10-series,
such as the power, control, video, and audio, can be
connected using a single triax cable. Various triax
connector types are supported; please contact your
local Sony office for details
Do NOT use a defective triax cable. The inner sheath of a triax
cable is used for power supply and the outer sheath for safety
ground. For your safety, do NOT use a triax cable whose inner
and outer sheaths are short-circuited. Use of such a cable may
cause electric shock.
b
b b
b
MIC OUTPUT (microphone output) connectors
(XLR 3-pin)
Supply the microphone signals from the video camera.
c
c c
c
RET1 through RET4 (return video 1 through 4
input) connectors (BNC type)
Accept the analogue return video signals from four
different sources. To select the appropriate return
signals use the RET1/RET buttons and RET2/3/4 switch
on the CA-570/P.
Note
When an optional BKP-7312 SDI input board is
installed, nothing should be connected to the RET 1
and RET 2 connectors in the ANALOGUE INPUT block.
d d d d
REFERENCE (reference signal input)
connectors (BNC type)
Accept a reference signal such as a black burst signal
for external synchronization.
e e e e
PROMPTER (prompter signal input) connectors
(BNC type)
Accept the signals for a teleprompter.
f f f f
R, G, and B (R, G, and B signal output)
connectors (BNC type)
Supply the analogue R, G, and B signals for the video
switcher, chroma keyer, or other destination from each
connector.
g g g g
Y, Cr, and Cb (component video signal output)
connectors (BNC type)
Supply the analogue Y, Cr, and Cb signals from each
connector. Connect a VTR or a video switcher
conforming to analogue component video signals.
h h h h
CHARACTER (character signal output)
connector (BNC type)
Supplies the self-diagnostic results of this unit as a
video signal.
i i i i
WF1 and WF2 (waveform monitor 1 and 2
output) connectors (BNC type)
Supply the video signals for a waveform monitor. The
MONITOR SELECT function on an RCP-750/751unit
select the signal output from the WF 1 connector, and
the WAVEFORM MONITOR buttons on the MSU-700A/
750 select the signal output from the WF 2 connector.
j j j j
PIX1 and PIX2 (picture monitor 1 and 2 output)
connectors (BNC type)
Supply the video signals for a picture monitor. The
MONITOR SELECT function on an RCP-750/751 unit
select the signal output from the PIX 1 connector, and
the PICTURE MONITOR buttons on the MSU-700A/750
select the signal output from the PIX 2 connector.
k
k k
k
VBS1, VBS2, and VBS3 (composite video signal
1, 2, and 3 output) connectors (BNC type)
Supply composite video signals (VBS) from the video
camera.
l
SYNC (sync signal output) connector (BNC type)
Supplies the sync signals (0.3 Vp-p, 75 ohms)
generated by the built-in sync signal generator.
Connect to the sync signal input connector of a
waveform monitor or picture monitor.
m m m m
AC IN (AC power input) connector
Connect to an AC power source using the supplied AC
power cord. The power cord can be fixed to the CCU-
700A/700AP using the supplied plug holder.
CCU-700P
110-120V
110-120V 220-240V
Ú
AC IN
CAMERA
REMOTE INTERCOM/TALLY/PGM
MIC OUTPUT
RTS
CH-1 CH-2
MIC
INTERCOM
COAX DIGITAL VIDEO
SERIAL OUTPUT SERIAL INPUT
RET 1 REFERENCE R Y WF1 VBS1
RET 2
PROMPTER
G R-Y PIX1 VBS2
RET 3 R B-Y WF2 VBS3
RET 4
RET 2 RET 1 1 2 3
CHARACTER
PIX2 SYNC
AUX
RCP/CNU
WF MODE
INPUT OUTPUT
REMOTE
1
CAMERA connector
2
MIC OUTPUT connectors
3
RET1 through RET4 connectors
4 REFERENCE connectors
5
PROMPTER connectors
ANALOG INPUT block
ANALOG OUTPUT block
6
R, G, and B connectors
7
Y, Cr, and Cb connectors
8 CHARACTER connector
9
WF1 and WF2 connectors
q;
PIX1 and PIX2 connectors
qa
VBS1, VBS2, and VBS3 connectors
qs
SYNC connector
qd AC IN connector
qf
WF MODE connector
qg
RCP/CNU REMOTE connector
qh
AUX REMOTE connector
qj SERIAL OUTPUT 1, 2, and 3 connectors
qk SERIAL INPUT RET 1 and RET 2 connectors
DIGITAL VIDEO block
ql
Spare connectors
w;
COAX connector
wa INTERCOM/TALLY/PGM connector
ws RTS connectors
wd
INTERCOM REMOTE connector
wf
MIC REMOTE connector
wg
Voltage selector