Sony BRC-H800, Руководство по эксплуатации

Страница: 9 / 65

9
* Turn the power off or to standby, then turn the power
on to reflect the changes after setting.
4
Baud Rate settings of RS-422 for VISCA
communication
* Turn the power off and on to reflect the changes
after setting.
567
Camera address settings
Sets camera address.
It is normally set to “Auto”. When “Auto” is
selected, an address is automatically assigned to the
camera.
To set the address manually, set a value between “1”
to “7” for this switch as indicated below.
* Turn the power off and on to reflect the changes
after setting.
N
U
(earth) terminal
O
HDMI OUT terminal
Supplies the images as an HDMI video signal.
* The contents of the menu screen, such as text, can
be displayed in the output signal when the OSD
switch is turned ON.
• When either 0 or 8 is selected for SYSTEM
SELECT, 2K output from the HDMI output
terminal results in lower quality images.
• When 7 is selected for SYSTEM SELECT, VGA
output from the HDMI output terminal results in
lower quality images.
P
VISCA RS-422 IN terminal
Connect with an remote controller (not supplied).
When you connect multiple cameras, connect it to
the VISCA RS-422 OUT terminal of the previous
camera in the daisy chain connection.
Q
VISCA RS-422 OUT terminal
When you connect multiple cameras, connect it to
the VISCA RS-422 IN terminal of the next camera
in the daisy chain connection.
R
MONITOR OUT
Outputs the image from the camera as a 4K or HD
signal.
4K output:
Connect the SDI 1 (3G-SDI) output to the SDI 1
input and the SDI 2 (3G-SDI) output to the SDI 2
input respectively.
HD output:
Connect to SDI 1 (3G-SDI) or SDI 2 (3G-SDI).
* The contents of the menu screen, such as text, can
be displayed in the output signal when the OSD
switch is turned ON.
* For the BRC-H800, only HD output is available.
S
OSD (On Screen Display) switch
The contents of the menu screen, such as text, can be
superimposed onto the video signal output to
MONITOR OUT & HDMI OUT when the switch is
turned ON.
T
LINE OUT
Outputs the image from the camera as a 4K or HD
signal. OSD (screen display) is not superimposed,
irrespective of the OSD switch setting.
4K output:
Connect the SDI 1 (3G-SDI) output to the SDI 1
input and the SDI 2 (3G-SDI) output to the SDI 2
input respectively.
HD output:
Connect to SDI 1 (3G-SDI) or SDI 2 (3G-SDI).
* For the BRC-H800, only HD output is available.
U
LAN (network) terminal (RJ-45)
Network communication and PoE+
*
power supply
are provided using the network cable (category 5e or
higher, shielded twist pair).
For more information on the connection, refer to the
instruction manual of the power supply system.
(
*
PoE+: an abbreviation of Power over Ethernet
Plus, which complies with IEEE802.3at)
The indicator lights up or flashes when the camera
is connected to the network. The indicator is off
when the camera is not connected to the network.
When connecting this product to a network, connect
via a system that provides a protection function,
such as a router or firewall. If connected without
such protection, security issues may occur.
Switch state Baud Rate
ON
38 400 bps
OFF 9600 bps
Switch No.
Camera address
5 6 7
OFF OFF OFF Auto
ON OFF OFF 1
OFF ON OFF 2
ON ON OFF 3
OFF OFF ON 4
ON OFF ON 5
OFF ON ON 6
ON ON ON 7
Notes
Note