Sony BKDM-3020 Скачать руководство пользователя страница 67

Страница: 67 / 78

4-3 (E)

4-1-2. BKDM-3010

The power cannot be turned on

Nothing appears on the monitor

BKDM-3010 cannot control DME-3000/7000

4-1. Trouble Shooting

Flow3

YES

The power of BKDM-3010
cannot be turned on.
(None of the CH1, CH2 and
GLBL buttons light up.)

Is the power of DME-3000/7000
turned on?

Is the connecting cable
connected correctly?
(Is the PROCESSOR connector
of BKDM-3010 connected to the
CONTROL PANEL connector of
DME-3000/7000?)

Is the voltage of the power supply
in DME-3000/7000 normal (-5V,
+12V)?
(For the voltage measurement ,
refer to the section 1-11.)

Turn the power of
DME-3000/7000 on.

Connect the 25-pin cable
between the PROCESSOR
connector of BKDM-3010
and the CONTROL PANEL
connector of DME-3000/7000.

Repair the power supply unit
of DME-3000/7000.

Repair the power supply circuit
on the CPU-119 board.

Flow4

YES

Nothing appears on the monitor.

Is the power of the monitor
turned on?

Is the RGB cable connected
correctly?

Is the luminance of the monitor
correct?

Turn the power of the
monitor on.

Connect the RGB cable to
the monitor.

Turn up the luminance.

Repair the display circuit on
the CPU-119 board.

Is the signal output from the
terminal of the monitor correctly?

YES

Replace the monitor with the new
one.

Flow5

YES

BKDM-3010 cannot control
DME-3000/7000.

Is the channel assign correct?

Is the switcher in DME WIPE
mode when DME-3000/7000 is
connected to the switcher?

Set the channel assign
correctly.

BKDM-3010 cannot control
DME-3000/7000 during DME
WIPE mode.

BKDM-3010 is faulty.

DME-3000/7000 is faulty

DME-3000:
Does the RUN indicator on the
CPU-114 board display "66"?

DME-7000:
Does the RUN indicator on the
CPU-196 board light up?

Содержание BKDM-3020















































































Результаты поиска

Содержание BKDM-3020

Отзывы:

Бренды по названию

Популярные бренды

Sony BKDM-3020, Руководство по обслуживанию

Результаты поиска

Содержание BKDM-3020

Отзывы:

Бренды по названию

Популярные бренды