Sony BKDF-701, Руководство по обслуживанию

Страница: 67 / 113

1-60
DFS-700/700P
Chapter 5 Control From Editing
Control Units
5-4
Chapter 5 Control From Editing Control Units
Procedure
To perform A/B roll editing by controlling the DFS-700/700P from the
PVE-500, use the following procedure.
Read this in conjunction with the PVE-500 Operating Instructions.
1
On the PVE-500, press the A/B button, turning it on.
2
On the PVE-500, select the FROM source and TO source.
The FROM source corresponds to the background on the DFS-700/
700P, and the TO source corresponds to the foreground.
3
Set the IN and OUT points for the FROM source, the TO source, and
the recorder, in any order.
Note
Because the DFS-700/700P has a built-in frame synchronizer, output
of player VCR edit points set on the PVE-500 is delayed by 1 frame,
so that recording begins with the previous frame. However, recorder
edit points are not delayed.
4
On the PVE-500, press the TRANS button, turning it on, and set the
transition duration.
5
On the DFS-700/700P, select the effect and make other settings as
required.
Note that the transition duration set on the PVE-500 takes priority.
6
Conduct a preview as required and execute the edit.
The edit is recorded as shown below.
Recorder and FROM
source IN points
,
FROM source OUT point
TO source IN point Recorder and TO
source OUT points
Recorder video Player A video Player B video Recorder video
Transition duration
Control From the PVE-500
Chapter 5 Control From Editing
Control Units
Chapter 5 Control From Editing Control Units
5-5
Control From the BVE-600
You can combine the DFS-700/700P with a BVE-600 Editing Control Unit
to carry out A/B roll editing using two players and one recorder.
The BVE-600 controls the DFS-700/700P using the GPI trigger signals T1
and T2.
Notes
• You cannot use the built-in switcher of the BVE-600 (BKE-611/612/621/
622) when you are using the DFS-700/700P.
• For details of preread editing, see the section “Preread Editing” (page 5-
14).
Preparations
Make the following preparations to control the DFS-700/700P from the
BVE-600.
For details of operation, refer to the BVE-600 Operating Instructions.
On the DFS-700/700P
• In page 1 of the setup menu, set F3(PORTS) to “BVE-600”.
• Press the EDITOR button on the control panel, turning it on.
(This button is lit when the DFS-700/700P is powered on.)
On the recorder VCR
• Set the recorder VCR so that it enters PB (playback) mode when stopped.
(If the VCR has a selector for PB or PB/EE, set it to PB.)
• If the VCR has a built-in TBC, set the VCR to DELAYED SYNC mode.
On the BVE-600
On the rear panel, set S502 DIP switch 3 and S503 DIP switch 2 to the
lower position (OFF), and power the BVE-600 on again.
When the unit is shipped from the factory, all DIP switches are set to the
upper position (ON).
Notes
• To display the background image during or after a transition, press an
appropriate BACKGROUND bus button on the DFS-700/700P.
• Because the DFS-700/700P has a built-in frame synchronizer, output of
player VCR edit points set on the BVE-600 is delayed by 1 frame, so that
recording begins with the previous frame. However, recorder edit points
are not delayed. For example, if the IN point of the player VCR is set to
00:00:10:15, actual recording begins from 00:00:10:14.
• The timing of the start of a transition is delayed by two frames from the
BVE-600 setting.