— 6 —
A-700T
5
EN
RESET
Horizontal size
The adjustment data becomes the unique setting for the
input signal received.
1
Press the
Å
+/– button.
The
Å
OSD (On Screen Display) appears.
2
Press the
Å
+/– button.
+ .... to enlarge
– .... to diminish
Vertical size
The adjustment data becomes the unique setting for the
input signal received.
1
Press the
+/– button.
The
OSD (On Screen Display) appears.
2
Press the
+/– button.
+ .... to enlarge
– .... to diminish
2
Press the
d
+/– button.
+ ... to expand the picture sides
– ... to diminish the picture sides
Pincushion
The adjustment data becomes the unique setting for the
input signal received.
1
Press the
d
+/– button.
The
d
OSD (On Screen Display) appears.
Rotation
The adjustment data becomes the common setting for all
input signals.
1
Press the
+/– button.
The
OSD (On Screen Display) appears.
2
Press the
+/– button.
+ .... to rotate clockwise
– .... to rotate counterclockwise
Resetting
•
Press the RESET button to recall the
factory settings for brightness, contrast,
pincushion, horizontal and vertical size,
and center for the mode currently in
use.
•
Press and hold the RESET button for 2
seconds to recall factory settings for all
adjustments in all modes.
Color Adjustment
This adjustment is common to all input signals received.
1
Press the + buttons of the
Raster Rotation and the
>
Contrast simultaneously. The OSD (On Screen Display)
appears.
2
Press the
>
+/– button.
+ .... for higher color temperature
– .... for lower color temperature
Press the +
buttons
simul-
taneously
6
Required
resumption time
—
approx. 3 sec.
approx. 3 sec.
approx. 10 sec.
State
Normal operation
Stand-by
(1st step of power saving)
Suspend
(2nd step of power saving)
Active-off
(3rd step of power saving)
Plug and Play
Damper Wire
Using a white background, very thin horizontal stripes on
the screen are visible as shown right. These stripes are the
damper wires. These wires are attached to the aperture
grille inside the Trinitron tube and are there to damp
vibrations of the aperture grille in order to prevent them
from influencing the picture quality.
Approx. 6 cm
Approx. 6 cm
Damper wire
Power Saving Function
This monitor meets the power-saving guidelines set by the
International
Energy Star Program as well as the more
stringent NUTEK 803299 (TCO92) guidelines. It is capable
of reduced power consumption when used with a computer
equipped with Display Power Management Signaling
(DPMS). By sensing the absence of the sync signal coming
from the computer, it will reduce the power consumption as
follows:
CAUTION:
The Power Saving function will automatically
put the monitor into Active-off state if the
power switch is turned on without any video
signal input. Once the horizontal and vertical
syncs are sensed, the monitor will
automatically return to its Normal operation
state.
Power consumption
110 W
15 W
15 W
8 W
u
Power indicator
green on
green on
green on
off
POWER SAVING
indicator
off
orange on
orange on
orange on
1
2
3
4
This monitor complies with the DDC
TM
1
,
DDC2B and
DDC2AB which are the Display Data Channel (DDC)
standards of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification Data) to the data line.
When a DDC2B or DDC2AB host system is connected, the
monitor automatically switches to each communication.
DDC
TM
is a trademark of Video Electronics Standard
Association.
•
Your monitor operates according to the VESA DDC Level
2AB. Only computers that support the same guidelines
and operate at the same or higher level can make use of
this feature.
•
If your computer does not support the relevant
guidelines, you can still use your monitor and computer.
You may need to specify manually the appropriate
resolution in the computer.
•
The highest resolution selected automatically may not
give the best result. In that case select the most suitable
resolution manually in the computer.