SONIX SN32F755 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 225

background image

SN32F760 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 66

Version 2.0

by the processor itself, memory systems and related controllers, and internal buses.

The power

state of the analog blocks (IHRC, EHS X’TAL, ELS X’TAL, PLL, Flash, LVD, ADC) is determined by the

enable bit of all blocks.

The processor state and registers, peripheral registers, and internal SRAM values are maintained and the logic levels
of the pins remain static.

Wake up the chip from Sleep mode by an interrupt occurs.

The RESET pin has keep functionality in Sleep mode.

The Sleep mode is entered by using the following steps:
1. Write 4 to

register.

2. Execute ARM Cortex-M0 WFI instruction.

4.3.2

DEEP-SLEEP MODE

In Deep-sleep mode, the system clock to the ARM Cortex-M0 core is stopped, and execution of instructions is
suspended.

The clock to the peripheral functions are stopped because the power state of oscillators are powered down, the clock
source are stopped, except RTC or LCD

low speed clock source (ELS X’TAL, ILRC) if used.



Note:

User SHALL decide to power down low speed clock source (ELS X’TAL, ILRC oscillator) or not

if RTC or LCD is enabled.

The processor state and registers, peripheral registers, and internal SRAM values are maintained and the logic levels
of the pins remain static.

All GPIO pins are served as wakeup pins. The user must program the GPIO registers for each pin to set the
appropriate edge polarity for the corresponding wakeup event, only edge sensitive is supported to wakeup MCU. The
system will exit Deep-sleep mode when GPIO indicates a GPIO interrupt to the ARM core. Furthermore, the interrupts
corresponding to each input must be enabled in the NVIC.

The RESET pin has keep functionality in Deep-sleep mode.

The Deep-sleep mode is entered by using the following steps:
1. Write 2 to

register.

2. Execute ARM WFI instruction.

The advantage of the Deep-sleep mode is that can power down clock generating blocks such as oscillators and PLL,
thereby gaining far greater dynamic power savings over Sleep mode. In addition, the Flash can be powered down in
Deep-sleep mode resulting in savings in static leakage power, however at the expense of longer wake-up times for the
Flash memory.

4.3.3

DEEP POWER-DOWN (DPD) MODE

In Deep power-down mode, power (Turn off the on-chip voltage regulator) and clocks are shut off to the entire chip with
the exception of the GPIO pins.

The processor state and registers, peripheral registers, and internal SRAM values are not retained. However, the chip
can retain data in four BACKUP registers, and the status of all GPIO pins can also be latched.

«
...
64
65
66
67
68
...
»

Содержание SN32F755


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SN32F755

Бренд: NCR Страницы: 6

Бренд: National Instruments Страницы: 2

Бренд: RAM Страницы: 71

Бренд: Eaton Страницы: 448

Бренд: HANYOUNG NUX Страницы: 4

Бренд: Haiwell Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: Blucave Страницы: 2

GUARDIAN CP DC2

Бренд: Amtrol Страницы: 12

Бренд: Taconova Страницы: 57

Бренд: North Star Страницы: 32

CALPOTE UF-1 Series

Бренд: SanRex Страницы: 26

Бренд: BIFFI Страницы: 52

Бренд: Athena Страницы: 24

Spatial FOG Dual ETH

Бренд: Advanced Navigation Страницы: 30

Бренд: MYERS Страницы: 27

Бренд: Samsung Страницы: 17

Бренд: HOBBYEAGLE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды